Upgrading Leaf Springs On 2022 Northwood Nash 23D OTG

Question

Question:

I have a 2022 Northwood Nash 23d OTG and I am wanting to upgrade the springs to the next size up. It has dual dexter 3500 lb axles. What info do I need to find the correct upgraded springs? I have a picture of the sticker on the axle if thats any help.

asked by: Brandon G

0

Expert Reply:

Hello Brandon, thanks for reaching out. To find the right springs we need to know the weight capacity of each axle, and we need to know the length of the leaf spring. We already know the capacity is 3,500 lbs so all you will need to do it jack up one side of the trailer and measure the leaf spring while not under a load. Leaf spring are measured from center-eye to center-eye. If you want to drop that measurement in the comments below I am happy to look into it and see if we have anything for you.

expert reply by: Jesse M

0

Brandon

11/10/2024

I just had a chance to do some measurements. They are 23.5 inches eye to eye jacked up by 1.75 inch wide springs. Its a 3 leaf pack but was also wondering if you guys have a slight heavier spring. Maybe 4k?

Jesse M.

11/11/2024

@Brandon We have a 23-1/8" long spring, part # e59SR which is rated for 3,500 lbs and is our closest option. Sadly we do not have anything 4K rated in this size. Our closest 4K rated spring is 25-1/4" long and this would not be a suitable replacement for your spring.

Answer 1

Hi Todd, To go with trailer leaf springs that are slightly stiffer than the 4,400 lb rating of your axle you can go with 4,500 lb springs or 5,000 lb springs. The right one is going to depend on the length of your current springs though, as…

view full answer...

Answer 2

Thanks for reaching out, David! We do have replacement top plates, like the U-Bolt Plate #TRTP238175 for a 2-3/8" diameter axle, or the U-Bolt Plate #TRU69FR for a 3" diameter axle. We also have a selection of 26" long leaf springs…

view full answer...

Answer 3

Hey John, You definitely weren't lying about those springs being flattened out. With them being flattened out they are going to be a bit wider so you will need a shorter eye-to-eye measurement than 26-1/4". My only concern is that the #e54SR…

view full answer...

Answer 4

Hi Jason; do you know the capacity of your Dexter axle? More arch for height isn't really a thing, and I wouldn't get longer shackles since that would throw off suspension geometry and be uneven since the front hanger stays the same. It is…

view full answer...

Answer 5

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Upgrading Leaf Springs On 2022 Northwood Nash 23D OTG

Product Page this Question was Asked From

Continue Researching