Where are Alignment Shims Installed on Timbren Axle-Less Suspension Kit
Updated 01/27/2026 | Published 08/26/2024
Question:
What is the use and method of this part?
asked by: Yongwoo
0
Shims in Timbren Axle-Less Kit
(click to enlarge)
(click to enlarge)
Expert Reply:
Hey Yongwoo, thanks for reaching out!
The pieces you highlighted from the Timbren Axle-Less Trailer Suspension Kit # TASR7KS01 are the alignment shims and are used when installing the spindle section to the main assembly.
Attached is a clip from the installation instructions showing where these go.
expert reply by:
Jon G
0
Timbren Axle-Less Suspension Assembly Diagram
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 5 Bolt Flange - 7,000 lbs
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- 7000 lbs
- Spindles Only
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Kenda Karrier KR53 ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel - 8 on 6-1/2
- Shop: etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 5,200 lbs to 7,000 lbs
- Shop: Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 5 Bolt Flange - 7,000 lbs
- Q&A: Looking For 7,000 lb Axle For HD Trailer
- Q&A: Availability of 6k or 7k Axles to Replace Lippert 3,500 lb Axles on Trailer
- Q&A: Timbren Axle-Less Replacement System for Outdoors RV Back Country Series 28DBS
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Shop: Trailer Axle w/ Electric Brakes - Easy Grease - 8 on 6-1/2 Bolt Pattern - 95" Long - 7,000 lbs
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Search Results: l44649
- Video: Replacement Round Fill Cap for Yakima RoadShower: The Breakdown
- Q&A: Replacement Bearings, Races & Seal For Timbren 3,500LB Axle-Less Suspension and 6,000LB Trailer Hubs
- Search Results: bearing kit
- Search Results: l44610
- Search Results: l68111
- Search Results: l68149
- Search Results: 15123 bearing
- Search Results: 15125
- Q&A: Which Bearings and Hubs Fit Heavy Duty 3,500 Lb Timbren Axle-Less Trailer Suspension
- Q&A: Correct Bearing Kit and Brakes for Timbren Axle-Less 3,500 System with 4" Lift
- Q&A: Proper Way to Tighten Trailer Spindle of Castle Nut
Kate F.
1/27/2026
Hey Yongwoo, how did things go with the alignment shims on your Timbren Axle-Less Suspension? Sharing how the install went could help others understand how those pieces fit into the assembly.