Bolts And Nuts Needed To Mount 12" Brake Assemblies

Question

Question:

My axle doesnt have studs for mounting these Dexter electric brakes, what size bolts and grade/material should be used?

asked by: Mason

0

Spindle
(click to enlarge)

Expert Reply:

Hey Mason,

To mount your 12" electric brake assemblies you would need the Mounting Bolts and Hardware for 12" Brake Assemblies # BRKH12.

expert reply by: Kevin C

0

Jesse M.

1/19/2026

Hey Mason, did the mounting bolts and hardware kit work out for your 12-inch Dexter brakes? Knowing how the fit turned out could help others trying to mount the same setup.

Answer 1

To replace your 12" brakes I recommend checking out the 7K TruRyde Electric Trailer Brake Kit #TRU96FR or the 5.2K - 7K Hydraulic Trailer Brake Kit #AKUBRK-7 depending on what kind of braking system you have. You'll also need the Mounting…

view full answer...

Answer 2

With having 22'6" from your tail light location to the tongue on your trailer I recommend going with at least a 30' wiring harness. The additional length is needed so you will be able to route your wiring on the frame to the lights and…

view full answer...

Answer 3

The method you described would be a great way to determine what length to cut the #H20046. That way you would end up with enough wire that it wouldn't come unplugged when making a tight turn. Securing the wire up and out of the way is a smart…

view full answer...

Answer 4

From my available specs on your M1101 trailer, it has a maximum vehicle weight of 3,400 pounds. It also looks like it uses off-road tires. With that capacity and tire type, we only carry 2,000 pound Timbren Axleless systems that are compatible with…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Bolts And Nuts Needed To Mount 12" Brake Assemblies

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching