Replacement Latch Only for Demco eZ-Latch Coupler

Question

Question:

I have a Demco EZ latch for a 2 5/16 ball. I need a new latch handle but only the composite latch handle. Demco shows the handle only on their website but you only show a repair kit with parts I dont need. Do you have the composite latch handle only?

asked by: William C

0

Expert Reply:

Hey William, thanks for reaching out!

We do have just the latch part out of the Demco Composite eZ-Latch Repair Kit # DM6008. What you're looking for is the part # DM29KR on our site.

expert reply by: Jon G

0

Bill

7/24/2024

Got it. Thank you.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Latch Only for Demco eZ-Latch Coupler

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching