What PSI Should Air Springs Be At On A 2023 Toyota Tundra Hauling A 7,500lb Trailer

Question

Question:

What pressure to use while towing with airlift system On 24 tundra, carrying 7500 pound trailer.

asked by: Adam W

0

Expert Reply:

Hey Adam,

There's too many factors involved to give you a specific psi rating that's going to level your ride and give you a comfortable ride quality. The best way to determine the right psi would be to couple up the trailer, level the ride out, and then take it on a test drive to see if the suspension needs to be stiffer or not and changing the psi in increments of 5psi.

expert reply by: Kevin C

0

Lazer S.

2/3/2026

Hey Adam, how did things go after you adjusted the air pressure on your Tundra with the trailer hooked up? Sharing what psi range worked best could really help others dialing in their Air Lift setup for towing.

Adam W.

2/3/2026

@LazerS It depends on how loaded I have the trailer and if it is windy or not. Generally, I set it at 15 -25. If the truck feels squirrely because of wind then sometimes I go as high as 40. Sometimes when you get to 40 though, the ride starts to be too rough. You also have to account for if you have a full truck of people or just 1 or 2 of you.

Lazer S.

2/3/2026

@AdamW Makes sense. That is the reason I like air bags though. They are the easiest way to get adjustable support when you need it! What kind of trailer are you towing?

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Brooks, we are located near St. Louis, MO in the US and we can ship to Canada. The K-Source tow mirrors part #KS48NQ are a confirmed fit for your 2026 Toyota Tundra TRD as well.

view full answer...

Answer 11

Hey Nick, yes I would say that the Curt TruTrack 2P Weight Distribution System #C67ZV is rated too high for your Jayco Jayfeather. This has a tongue weight range of 800-1,000 lbs and you'd most likely have a tongue weight around 640 to 750 lb.…

view full answer...

Answer 12

Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…

view full answer...

What PSI Should Air Springs Be At On A 2023 Toyota Tundra Hauling A 7,500lb Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching