Replacement Hardware Kit For Draw-Tite Receiver 65070 For 2017 Toyota Tacoma

Question

Question:

I have a draw tite front hitch for 2017 Tacoma 65070 and I need a parts kit to install. Can I purchase this from you?

asked by: Barry H

0

Expert Reply:

To get the replacement hardware for the Draw-Tite Receiver # 65070 you will need to order the Replacement Hardware Kit # RHK and type the hitch item number on the line provided.

expert reply by: Bud M

0

Answer 1

I do have both front mount hitch and grille guard options for your 2017 Toyota Tacoma TRD Off Road but as you mentioned they cannot be used together and I am not aware of any grille guards that have an integrated receiver tube. Therefore, you will…

view full answer...

Answer 2

We do have the Firestone Ride-Rite Air Helper Springs #F2407 that will fit your 2006 Toyota Tacoma Pre-Runner. Please note that your axle will need to be located below the leaf spring pack for this to fit. You might also be interested in an air…

view full answer...

Answer 3

The Curt Front Mount Hitch #31313 being able to accommodate your dirt bike will really depend on the weight of the bike. There are also a variety of factors that go into carrying something of that size in front of your vehicle. The etrailer…

view full answer...

Answer 4

The front-mount hitch that best meets your requirements is the Draw-Tite #65070. This will allow you to re-install your skid shield after you bolt on the hitch. I recommend this model also because it offers a higher vertical load capacity of 500-lbs,…

view full answer...

Answer 5

You should be able to reinstall your skid plate after installing the Curt Front Hitch #31313. On the older models (prior to 2007) the skid plate isn't required to be removed. The newer ones after 2007 do require the removal of it, but we had a…

view full answer...

Answer 6

Normally the skid plate can reinstall after the front hitch part #31313 is installed but on the TRD models the skid plate is different and can't be.

view full answer...

Answer 7

Draw-Tite front-mount hitch #65070 is a confirmed fit on your 2012 Toyota Tacoma 4WD. We have not had a chance to install this particular item nor the Curt equivalent #31313 on your same truck so for purposes of seeing the effect on your ground…

view full answer...

Answer 8

Yes the DrawTite Front Mount Trailer Hitch Receiver part #65070 is a confirmed fit for your 2016 Tacoma TRD. It will work on all models of the Tacoma from 2005-2020. It offers a straight forward installation. I linked the video of the installation we…

view full answer...

Answer 9

Yes, the TRD skid plate will need to be removed or heavily modified to reinstall on a 2019 Toyota Tacoma with front mount trailer hitch like the Draw-Tite Front Mount Trailer Hitch Receiver part #65070. Unfortunately, they both just simply mount in…

view full answer...

Answer 10

We have two front-mount trailer hitches for your 2017 Tacoma. I called my contact at Curt and they said that when installing the #C31075 hitch the air dam will need to be trimmed as shown in the attached installation instructions. The photo on the…

view full answer...

Answer 11

There are few differences between the Draw-Tite Front Mount Trailer Hitch Receiver #65067 and Curt Front Mount Trailer Hitch Receiver #C31083 that fit your 2020 Ford F-150, with the main difference being ground clearance. The Curt hitch does have…

view full answer...

Answer 12

I do have an option that will allow for you to still have your skid plate on your 2008 Toyota Tacoma as with the Curt Front Mount Trailer Hitch Receiver #31313 mounted to the front of your Tacoma the skid plate must be permanently removed and not…

view full answer...

Replacement Hardware Kit For Draw-Tite Receiver 65070 For 2017 Toyota Tacoma

Products Featured in This Question

Continue Researching