Replacement Fender For Drivers Side Of a 2018 Winnebago Winnie Drop 170K Travel Trailer

Question

Question:

2018 Winnebago WD170K trailer fender leftside. Is this the right part?

asked by: Daniel C

0

Expert Reply:

While I have no way to lookup exactly what fenders are installed on your 2018 Winnebago Winnie Drop 170K I do see it has 14" wheels from the factory. This would mean the Fender # HP38VR would be the most likely candidate. But you will want to take measurements off your fender to verify the correct size. This fender is 9" Wide by 30" long and 13-1/4" tall. The Fender # HP56VR you found is for 15" wheels and is 9" Wide by 32" long and 15" tall. If your fender is different in size from either of these please let me know what you find and I can verify if we have one which will fit.

It does appear your camper uses the LED Trailer Fender Clearance Light # DG52444VP based on the images I could find.

expert reply by: Bud M

0

Daniel C.

6/14/2024

I bought the fender and it was the exact same fender on my trailer

Bud M.

6/14/2024

@DanielC Thank you for the update. This will surely help others in the future to know the Fender # HP56VR was the correct one.

Daniel

6/21/2024

@DanielC I was mistaken it's not the same it's really close, just a few inches long. It's not the exact fit fir my Winnebago WD170K

Answer 1

I have looked through the various steel trailer fenders we offer, and have not found any that match the exact measurements you provided. The closest fender I found was the CE Smith Pre-Galvanized Steel Fender, part #CE17701G. This fender measures…

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Hey Don! The sides of the #CE17900G are slightly rounded but you can still bolt it directly to the wall of your 2017 R-Pod 179. I attached a picture below showing where another customer was able to attach it directly to the side of his trailer so you…

view full answer...

Answer 4

The first thing you will need to do is find the bolt pattern on your trailer wheels. From what I have found, you have a 5 on 4-1/2 bolt pattern on your current wheels, but you will want to confirm this. The other thing you are going to need to do is…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The length of a fender is measured from the longest point, at the very bottom of each end across. Then the height is measured from the tallest point, right in the center. For example, the CE Smith Single Axle Trailer Fender #CE17720 is 22-1/2"…

view full answer...

Answer 7

The Replacement Spring for Reese and Draw-Tite Fifth Wheel Trailer Hitches #30776 you were looking at connects from the actuating rod to the hitch head, and a second spring goes from the hitch head to the jaws. These springs hold the actuating rod…

view full answer...

Answer 8

The closest fender we have to the specs you sent in is the Single Axle Trailer Fender for Enclosed Trailer for 13" to 15" Wheels #HP66FR which measures 36" long x 10-3/4" wide x 20" tall and installs using the Mounting…

view full answer...

Replacement Fender For Drivers Side Of a 2018 Winnebago Winnie Drop 170K Travel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching