Replacement Right Rear and Right Center Jacks for Lippert Ground Control 6 Point 3.0

Question

Question:

I have a 6 point 3.0 lippert leveling system. I need to replace the driver side center leg and the driver side rear leg. What leg legs do I need to buy?

asked by: Jim W

0

Expert Reply:

Hey Jim, so the correct replacement center right jack for your Ground Control 3.0 6 point system is the part # LC344792 which is also correct for right rear.

expert reply by: Jameson C

0

Answer 1

Since the Lippert stabilizer jack motor can clearly work since it can extend but not retract that to me sounds like a bad switch which we offer with the part #LC144214.

view full answer...

Answer 2

For your Lippert Ground Control 3.0 Leveling System, the driver side middle jack replacement you need is the Replacement Left Rear Leg for Lippert Ground Control 3.0 Electric 6 Point Leveling System #LC342610 which has an outer leg that measures 17…

view full answer...

Answer 3

It is possible that the Replacement 22-1/2" Right Rear Leg for Lippert Ground Control 3.0 Electric Leveling System #LC428493 you were looking at will be the correct replacement right middle jack for your 6 point Lippert Ground Control 3.0, but…

view full answer...

Answer 4

The Ground Control jacks for travel trailers are different as they are a C-jack instead of a vertical lift. I recommend using the Replacement C-Jack for Lippert Components Electric Ground Control TT #LC404488 for that application instead of combining…

view full answer...

Answer 5

Yes, the left rear leg for the Lippert Ground Control 3.0 Electric 4 Point Leveling System is the same as the left middle leg for the Lippert Ground Control 3.0 Electric 6 Point Leveling System. If your left middle leg measures 17" long then you…

view full answer...

Answer 6

Yes, we do offer replacement jacks for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set part #LC675817. I have attached these for you below by their location on the trailer. Rear/Middle: 24-1/2" Leg part…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Right Rear and Right Center Jacks for Lippert Ground Control 6 Point 3.0

Product Page this Question was Asked From

Continue Researching