Retracted Height of Bulldog # BD155033 A-Frame Trailer Jack

Question

Question:

Is the retracted height measured from the bottom of A-frame mounting plate to the ground? I have a 2014 US Cargo Patriot Car Hauler Model PACX8520TA2 with a 7000 lb GVWR. The tongue height is 18inch fromt he ground to the bottom of the hitch. The original jack damaged is rated at 2000 lb lift and 3000 Lb support. Which jack woiuld you recommend to repalce the dmaged one?

asked by: Ron G

0

Expert Reply:

The Bulldog # BD155033 has bottom of mounting bracket to bottom of inner tube dimension of 5-13/16 inches when the jack is fully retracted. Its 2000 lb lift capacity is more than enough to handle the tongue weight of your trailer.

expert reply by: Mike L

0

click to enlarge

Answer 1

We have checked with Bulldog in the past about the replacement options for the Bulldog A-Frame Jack part 1551060301 that you have and they were able to give us all of the information we need to offer you a solution. The best option we have is the…

view full answer...

Answer 2

We have 2,000 lb A-frame jacks made by the same parent company Cequent that your jack was made by with the Pro Series jack part #PS1401000303 which is a topwind. I attached a review video for more info on this as well.

view full answer...

Answer 3

From the bottom of the mounting bracket down to the bottom of the outer tube measures 3-1/2 inches on the Pro Series jack part #PS1401000303 that you referenced.

view full answer...

Answer 4

As long as your jack stand has a 2" outer diameter tube then, yes, you could use the Bulldog #BD155033 in this manner. This jack has a 15" lift and a 2000-lbs capacity, so you would want to make sure that you're going off the capacity…

view full answer...

Answer 5

Yes the Bulldog Round A-Frame Jack, #BD155033, will work well for your Carry-On model trailer. The jack has a 2000 lbs lift capacity and a total of 15 inches of lift. The mounting bracket on the jack is usually an universal fit. To make your that…

view full answer...

Answer 6

I called Bulldog about the Bulldog A-Frame Jack part 1551060301 that you are wanting to replace and they were able to give me all of the information I need to offer you a solution. The best option we have is the Bulldog Round A-Frame Jack part…

view full answer...

Answer 7

I went out to our warehouse to take a look at the Buyers Products A-Frame Jack #3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have…

view full answer...

Answer 8

The difference between 5-1/2 inches and 5-2/5 inches is 1/10 of an inch and would most likely not make a noticeable difference. However, if you were looking for the absolute shortest retracted distance you would want the Bulldog Round, A-Frame Jack,…

view full answer...

Answer 9

Bulldog A-frame jacks like the #BD155033 are made overseas, but there are some Made in the USA options available. If you're looking for an American made A-Frame trailer jack, the A-Frame Trailer Jack - Topwind - 2,000 lbs. by Dutton-Lainson…

view full answer...

Answer 10

Hey Bob, I don't know of any safety concerns regarding the Bulldog Round, A-Frame Jack #BD155033 and the tongue weight does not change. This jack has a 2,000 lb lift capacity, so as long as your trailer's tongue weight is less than 2,000 lbs,…

view full answer...

Answer 11

From the bottom of the mounting plate to the bottom of the outer tube is 3-1/4 inches on the Pro Series Round, A-Frame Jack #PS1401000303. I've attached a picture as well.

view full answer...

Answer 12

Yes we do, the jack you are looking for is our part number #BD15164.

view full answer...

Retracted Height of Bulldog # BD155033 A-Frame Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching