Will the Bulldog Top Wind Trailer Tongue Jack Work on a Carry-On Trailer

Question

Question:

I need a replacement jack for my carry on trailer. Will the BullDog version fit? part# 155033?? I cannot find the model number of my Carry On Trailer.

asked by: Patrick H

0

Expert Reply:

Yes the Bulldog Round A-Frame Jack, # BD155033, will work well for your Carry-On model trailer.

The jack has a 2000 lbs lift capacity and a total of 15 inches of lift. The mounting bracket on the jack is usually an universal fit. To make your that this jack will fit, measure your current jack to see if the outer tube diameter is at least 2-1/4 inches. If your jack is not bigger than this measurement then the Bulldog jack will fit.

expert reply by: Jared P

0

Answer 1

We have checked with Bulldog in the past about the replacement options for the Bulldog A-Frame Jack part 1551060301 that you have and they were able to give us all of the information we need to offer you a solution. The best option we have is the…

view full answer...

Answer 2

The difference between 5-1/2 inches and 5-2/5 inches is 1/10 of an inch and would most likely not make a noticeable difference. However, if you were looking for the absolute shortest retracted distance you would want the Bulldog Round, A-Frame Jack,…

view full answer...

Answer 3

I called Bulldog about the Bulldog A-Frame Jack part 1551060301 that you are wanting to replace and they were able to give me all of the information I need to offer you a solution. The best option we have is the Bulldog Round A-Frame Jack part…

view full answer...

Answer 4

Bulldog A-frame jacks like the #BD155033 are made overseas, but there are some Made in the USA options available. If you're looking for an American made A-Frame trailer jack, the A-Frame Trailer Jack - Topwind - 2,000 lbs. by Dutton-Lainson…

view full answer...

Answer 5

We have 2,000 lb A-frame jacks made by the same parent company Cequent that your jack was made by with the Pro Series jack part #PS1401000303 which is a topwind. I attached a review video for more info on this as well.

view full answer...

Answer 6

As long as your jack stand has a 2" outer diameter tube then, yes, you could use the Bulldog #BD155033 in this manner. This jack has a 15" lift and a 2000-lbs capacity, so you would want to make sure that you're going off the capacity…

view full answer...

Answer 7

Hey Bob, I don't know of any safety concerns regarding the Bulldog Round, A-Frame Jack #BD155033 and the tongue weight does not change. This jack has a 2,000 lb lift capacity, so as long as your trailer's tongue weight is less than 2,000 lbs,…

view full answer...

Answer 8

I went out to our warehouse to take a look at the Buyers Products A-Frame Jack #3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have…

view full answer...

Answer 9

From the bottom of the mounting plate to the bottom of the outer tube is 3-1/4 inches on the Pro Series Round, A-Frame Jack #PS1401000303. I've attached a picture as well.

view full answer...

Answer 10

The Bulldog #BD155033 has bottom of mounting bracket to bottom of inner tube dimension of 5-13/16 inches when the jack is fully retracted. Its 2000 lb lift capacity is more than enough to handle the tongue weight of your trailer.

view full answer...

Answer 11

Yes we do, the jack you are looking for is our part number #BD15164.

view full answer...

Answer 12

From the bottom of the mounting bracket down to the bottom of the outer tube measures 3-1/2 inches on the Pro Series jack part #PS1401000303 that you referenced.

view full answer...

Will the Bulldog Top Wind Trailer Tongue Jack Work on a Carry-On Trailer

Continue Researching