Trailer Jack Recommendation for an A-Frame TrailCruiser Trail-Lite 21RBH

Question

Question:

We removed and lost our broken stock trailer jack and are trying to replace for an A-frame TrailCruiser Trail-lite 21RBH. It has a 4 frame depth which seems to require a jack with a very short retracted distance between jack bracket and bottom of retracted tube. Are we looking for 5-1/2 or 5-2/5 ?

asked by: Desi F

0

Expert Reply:

The difference between 5-1/2 inches and 5-2/5 inches is 1/10 of an inch and would most likely not make a noticeable difference.

However, if you were looking for the absolute shortest retracted distance you would want the Bulldog Round, A-Frame Jack, part # BD155033. I went out into our warehouse and compared this jack with the Pro Series Round, A-Frame Jack, part # PS1401000303, and found it to be the shorter of the two.

You may be interested in purchasing a Bulldog Removable wheel, part # BD500245, or a Bulldog Jack Support Plate, part # BD003135.

expert reply by: Jameson C

0

Answer 1

We have checked with Bulldog in the past about the replacement options for the Bulldog A-Frame Jack part 1551060301 that you have and they were able to give us all of the information we need to offer you a solution. The best option we have is the…

view full answer...

Answer 2

As long as your jack stand has a 2" outer diameter tube then, yes, you could use the Bulldog #BD155033 in this manner. This jack has a 15" lift and a 2000-lbs capacity, so you would want to make sure that you're going off the capacity…

view full answer...

Answer 3

We have 2,000 lb A-frame jacks made by the same parent company Cequent that your jack was made by with the Pro Series jack part #PS1401000303 which is a topwind. I attached a review video for more info on this as well.

view full answer...

Answer 4

I went out to our warehouse to take a look at the Buyers Products A-Frame Jack #3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have…

view full answer...

Answer 5

From the bottom of the mounting bracket down to the bottom of the outer tube measures 3-1/2 inches on the Pro Series jack part #PS1401000303 that you referenced.

view full answer...

Answer 6

From the bottom of the mounting plate to the bottom of the outer tube is 3-1/4 inches on the Pro Series Round, A-Frame Jack #PS1401000303. I've attached a picture as well.

view full answer...

Answer 7

Yes the Bulldog Round A-Frame Jack, #BD155033, will work well for your Carry-On model trailer. The jack has a 2000 lbs lift capacity and a total of 15 inches of lift. The mounting bracket on the jack is usually an universal fit. To make your that…

view full answer...

Answer 8

Yes we do, the jack you are looking for is our part number #BD15164.

view full answer...

Answer 9

The Bulldog #BD155033 has bottom of mounting bracket to bottom of inner tube dimension of 5-13/16 inches when the jack is fully retracted. Its 2000 lb lift capacity is more than enough to handle the tongue weight of your trailer.

view full answer...

Answer 10

I called Bulldog about the Bulldog A-Frame Jack part 1551060301 that you are wanting to replace and they were able to give me all of the information I need to offer you a solution. The best option we have is the Bulldog Round A-Frame Jack part…

view full answer...

Answer 11

Hey Bob, I don't know of any safety concerns regarding the Bulldog Round, A-Frame Jack #BD155033 and the tongue weight does not change. This jack has a 2,000 lb lift capacity, so as long as your trailer's tongue weight is less than 2,000 lbs,…

view full answer...

Answer 12

Bulldog A-frame jacks like the #BD155033 are made overseas, but there are some Made in the USA options available. If you're looking for an American made A-Frame trailer jack, the A-Frame Trailer Jack - Topwind - 2,000 lbs. by Dutton-Lainson…

view full answer...

Trailer Jack Recommendation for an A-Frame TrailCruiser Trail-Lite 21RBH

Continue Researching