Does The etrailer Hard Tonneau Cover # e83DR Fit Flush On a 2024 Ford Ranger 5' Bed?

Question

Question:

Looks like it doesnt fit flush? 2024 ranger xlt

asked by: Ken S

0

Expert Reply:

The etrailer Hard Tonneau Cover # e83DR for your 2024 Ford Ranger XLT 5' bed is going to sit approximately 1" above the bed rails. If you are wanting a flush cover check out the BAKFlip MX4 # BAK448332. It has an aluminum construction with a clean matte black finish.

expert reply by: Bud M

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 3

Hi Brian, To flat tow your 2026 Ford Ranger XLT with your Blue Ox Avail Tow Bar, you'll need: - Blue Ox Base Plate Kit w/Removable Arms part #BLU77ER, this will require some minor drilling, and the tow hooks must be removed and remain off the…

view full answer...

Answer 4

Using the cut off wiring harness you have for the P3 part #90195 you will wire it to the brake controller wiring of your 2023 Ford Ranger which is sticking out of the large wire harness that goes through the driver's side firewall, left of the…

view full answer...

Answer 5

Hello again, Randall, thanks for reaching out. I looked everywhere and I also was not able to find the exact T-slot size listed anywhere. I do know the bars use standard T-slots, so any accessory that is also made for standard T-tracks should work…

view full answer...

Answer 6

Hey Jim; the Curt RVibrake Shadow 2 #RVI94FR is not compatible with your 2026 Maverick. Initially it was listed as a fit but Curt/Lippert came out with an exclusion list that includes the Maverick Hybrid. Right now it is listed as 2022-2025 but it…

view full answer...

Answer 7

Good question Matt, you've definitely done your homework! Yes, your understanding is correct. The Replacement Fast Grip Clamp #TH94JV is the same mounting clamp used on the Thule Pulse Large cargo box #TH615. The FastGrip clamps are designed to…

view full answer...

Answer 8

Since your 2020 Ford Ranger SXT came with a factory installed 7-way trailer connector, you should have a brake controller connector under the dash. That being said, the connector that would most likely fit #3034-P, has not been confirmed as a fit for…

view full answer...

Answer 9

Hi Mike, what exactly are you looking for? You looked at a weight distribution hitch (WDH), are you trying to find the right one for your setup? If you are, can you tell me more about your trailer? To find the right WDH it is important to know the…

view full answer...

Answer 10

Hey David, the Redarc Tow-Pro Link Bluetooth Brake Controller #RED57AR that you referenced will fit any vehicle that has a 7-way installed on it including your 2017 Ram 3500 that has a factory brake controller. This will bypass that circuit on your…

view full answer...

Answer 11

Hello Gary, thanks for providing all of the info and part numbers for your awning. That does come back as one of the Lippert 2000 series awnings. It sounds like you might be looking for the Replacement Pitch Arm Assembly #LC93BX which is for the 2000…

view full answer...

Answer 12

Hi Jesus, The number you provided comes back as a Solera Edge awning in black, but we'll need a bit more information to determine the correct arm because there's 3 different models in black. There should be another sticker on the arm with a…

view full answer...

Does The etrailer Hard Tonneau Cover # e83DR Fit Flush On a 2024 Ford Ranger 5' Bed?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching