Does Installation of Curt Front Hitch on 2017 Chevrolet Suburban Require Drilling

Question

Question:

Are the holes in the frame pre drilled. 2017 suburban

asked by: Jim K

0

Expert Reply:

Hi Jim; you will have to drill holes in the frame to install the # C31073 which can be seen in the instructions below. The holes are not pre-drilled.

expert reply by: Robin H

0

Curt Instructions
(click to enlarge)

Answer 1

As you mentioned, the Curt #C31073 and Draw-Tite #65064 are the only front mounted receivers we offer for your 2020 Chevy Tahoe. Both hitches have the receiver located under the front bumper, which is necessitated by the way the vehicle front clip…

view full answer...

Answer 2

You are going to have to trim out a section of your front air dam to install the Curt Hitch part #C31073 that is 3 inches wide by 1.50 inches tall. A similar amount of trimming is required for the Draw Tite hitch part #65064 as well. The other option…

view full answer...

Answer 3

Yes, there is! To add a front hitch to your 2018 Chevy Suburban, I recommend the Curt item #C31073. This front mounted hitch is custom fit and bolts to your Chevy with included hardware. This hitch has a 2" receiver, with a 5,000 lbs towing…

view full answer...

Answer 4

We have a great front mount hitch option confirmed to fit your 2016 Tahoe with the Z71 off road option, the Draw-Tite Front Mount Trailer Hitch Receiver #65064. According to the linked installation instructions, you may need to lower or loosen the…

view full answer...

Answer 5

As far as ground clearance goes for your 2015 Chevy Suburban you will want to use the Curt Front Mount Trailer Hitch Receiver #C31073 over the Draw-Tite Front Mount Trailer Hitch Receiver #65064 because the instructions call for you to cut the front…

view full answer...

Answer 6

The correct Draw-Tite Front Mount Trailer Hitch Receiver for a 2019 Chevrolet Silverado 1500 LD is part #65064 which is for the old body style models. Therefore, you will essentially be looking at products for the 2018 model year. If you select 2019…

view full answer...

Answer 7

For your 2018 Chevy Suburban the Curt Front Mount Trailer Hitch Receiver #C31073 and the Draw-Tite #65064 will both require air dam trimming. I've linked a couple photos to assist. The dimensions of the Curt cutout diagram is shown and then the…

view full answer...

Answer 8

Yes! The Draw-Tite Front Mount Trailer Hitch Receiver #65064 does not require any drilling in the frame of your 2018 Chevy Silverado 1500 for the installation. The instructions do call for you to remove or trim the lower air dam fascia, which is a…

view full answer...

Answer 9

You are going to have to trim out a section of your front air dam to install the Curt Hitch part #C31073 that is 3 inches wide by 1.50 inches tall. A similar amount of trimming is required for the Draw Tite hitch part #65064 as well. The other option…

view full answer...

Answer 10

As far as ground clearance goes for your 2017 Chevy Tahoe you will want to use the Curt Front Mount Trailer Hitch Receiver #C31073 over the Draw-Tite Front Mount Trailer Hitch Receiver #65064 because the instructions call for you to cut the front…

view full answer...

Answer 11

The front mount trailer hitch options for a 2019 Chevrolet Tahoe, the Curt Front Mount Trailer Hitch Receiver part #C31073 and Draw-Tite Front Mount Trailer Hitch Receiver part #65064 both require a slight trimming of the front lower bumper fascia. I…

view full answer...

Answer 12

Yes it will; the vertical load capacity is 500 lbs for the hitch so that's the limit on any type of carrier (and it's accompanying cargo). So as long the motorcycle carrier is 200 lbs or less, you can carry a 300 lb motorcycle with your 2019…

view full answer...

Does Installation of Curt Front Hitch on 2017 Chevrolet Suburban Require Drilling

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching