How Can I Eliminate Sag On A 2022 Ford Bronco Badlands With Sasquatch Package

Question

Question:

I have a 2022 Ford Bronco Badlands with the Sasquatch package. I pull a small off road trailer and would like to eliminate the sag in the rear while pulling the trailer with the truck loaded. Any suggestions?

asked by: Bob M

0

Expert Reply:

Hello Bob, thanks for reaching out. Unfortunately, the sasquatch package is going to be a major limiting factor for your suspension enhancement option. Currently none of the aftermarket suspension upgrades we offer will fit a 2022 Bronco with the sasquatch package. This is also true for the Wildtrak and Raptor models.

Adding a weight distribution hitch to the trailer would be one way to help level your ride, since there are no options for the vehicle side. If you can tell me the GVWR of your trailer I am happy to make a recommendation. I will also need to know if your trailer has a straight tongue or an A-frame tongue.

expert reply by: Jesse M

0

Answer 1

Hey Mike! The Power Mountain Tallboy Off-Road Bottle Jack #PM34FR can be stored in that manner (with the oil plug facing up), but my contact at Power Mountain stressed that it should only be done for a short period of time, so I recommend setting it…

view full answer...

Answer 2

The best SumoSprings for your 2023 Ford Bronco depends on what you are using them for - just to improve your ride a bit on rougher roads, or to help with sag when you are towing or maybe using an accessory. I'll go ahead and list out the options…

view full answer...

Answer 3

While we have an option for you, the SumoSprings Custom Helper Springs #SS56EV will not work with the 2 inch spacer lift on your 2022 Ford Bronco. Instead, for suspension help I recommend using the Coil SumoSprings Custom Helper Springs for Coil…

view full answer...

Answer 4

Yes, the SumoSprings Custom Helper Springs #SS56EV will fit your 2021 Bronco. The Badlands trim with the Sasquatch package will not interfere with the installation. These work for both the 2WD and 4WD models and have a 1,000 lb weight capacity. They…

view full answer...

Answer 5

Hey Chris! SumoSprings typically recommends a 1/2" - 1" gap between the helper springs and the point of contact. The larger the gap the longer it takes for the springs to engage and vice versa. The 1/2" spacers that come with the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hello Kevin, Thanks for writing in. The main difference between the Power Watchdog Surge Protectors #HU67FR and #HU42VR comes down to the monitoring capability, housing design, and surge protection rating. The #HU67FR is the newer Generation 2 model.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

How Can I Eliminate Sag On A 2022 Ford Bronco Badlands With Sasquatch Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching