Dimensions Across of Curt Hitch 13208

Question

Question:

I have a 1953 Chevy 3200 pickup with a tailgate pan and Im looking to put a rear bumper and trailer hitch on it. Can you give me the dimensions on the 13208 receiver drawing I attached. The height from the top of the end brackets to the receiver centerline. The distance center to center on the end brackets.

asked by: Ted A

0

Dimensions Needed
(click to enlarge)

Expert Reply:

Hello Ted,

The Curt Trailer Hitch Receiver # 13028 measures 31-1/8 inches across, and the height from the top of the brackets to the receiver is 5 inches.

expert reply by: Kyle S

0

Answer 1

The Curt #13323 and the Draw-Tite #75236 Class III hitches share the same weight capacity and installation procedure. The appearance and design of the two hitches are pretty similar. As far as quality goes, both brands are about equal. Given this,…

view full answer...

Answer 2

Most likely the Curt hitch part #13323 that you tried to install was bent in shipping as that hitch is a fit for your vehicle and unfortunately hitches do sometimes get bent in shipping. It's very easy for them to get bent in to make them seem to…

view full answer...

Answer 3

Yes, the Curt Trailer Hitch Receiver #C13900 will fit a 2005 -2015 Toyota Tacoma. To properly install the hitch you will use the bolt holes "A" and "C" in the diagram, they will fit existing holes and doesn't require any…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Dimensions Across of Curt Hitch 13208

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching