Can the 2-Tang Clevis for BulletProof Hitches Ball Mounts 358CLEVIS Be Used w/ a Lunette Ring?

Question

Question:

Can this be used to tow a trailer with a lunet ring? Or should I get a dedicated pintle hitch?

asked by: Brent

0

Expert Reply:

Yes, it can! The 2-Tang Clevis for BulletProof Hitches Adjustable Ball Mount item # 358CLEVIS has been designed to work with trailer's that have a lunette ring. It has a 20,000 lbs capacity and works with ball mounts like item # HD2512.

expert reply by: Jerred H

0

Answer 1

Hey Brent! No, the factory brake controller on your 2016 Ram 2500 is pretty easy to swap out with one like the Tekonsha Prodigy P2 item #90885. You'll need to remove the dash panel around your factory controller, pull the unit out of the dash,…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Jen, thanks for the information! Since your 2016 Ram 2500 has the Ram Boxes, you'll need to have a rotating pin box installed on your 2026 Jayco Eagle HT DDB. The rotating pin box is the only way to tow a 5th wheel trailer and not hit the Ram…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can the 2-Tang Clevis for BulletProof Hitches Ball Mounts 358CLEVIS Be Used w/ a Lunette Ring?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching