What Comes with Trailer Axle # e25GR

Question

Question:

Hi what comes with the e25GR?

asked by: Rip

0

Expert Reply:

Hey Rip, so the trailer axle part # e25GR comes with hubs that are loaded with bearings, races, grease, and a seal as well as lug nuts to attach a wheel.

expert reply by: Jameson C

0

Answer 1

For a standard axle we have the Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern #e25GR which is rated for 2,000 lbs but the spring seats are 48" apart on center so for this to fit you'll have to cut off the current sets and have new ones,…

view full answer...

Answer 2

Since you have 12 inch wheels you would have to go with a smaller hub/drum to fit underneath them. The standard size that would fit under a 12 inch rim is 7 x 1-3/4 like the part #AKHD-545-2-EZ-1K which fits most 2k axles. But first we need to figure…

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

The TruRyde Spindle #TRU94FR and our Trailer Idler Hub Assembly #AKIHUB-545-2-2K are not compatible, but you could use the TruRyde EZ Lube Spindle #TRU44FR instead as it has the correct spindle measurements. For a hub that will work with the TruRyde…

view full answer...

Answer 5

I went and pulled a coupler like you have part #BD44150W0317 and the coupler lock you are interested in part #BLTL-20 and found that they lock is wide enough to fit this coupler. I attached a picture that shows the two products next to each other to…

view full answer...

Answer 6

Hey Rick, Thanks for your question. The Grease Cap Plug for Dexter Axle E-Z Lube Grease Caps - Qty. 2 #DX89HR is the correct replacement for your torn rubber plug. Since it's a Dexter-branded part, it's a great choice if you're looking to…

view full answer...

Answer 7

The tire/wheel combination products that we offer come from the manufacturer already pre-mounted. The tire's low spot is matched to the rim's high spot when they are mounted together. This is not the same as an actual dynamic tire balancing…

view full answer...

Answer 8

When using the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles part #e27SR with the Single-Axle Trailer Hanger Kit for Double-Eye Springs part #APS4 you will need to space the leaf spring hangers 25-3/4" apart.

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

Yes, you can change from 1-3/4 inch slipper springs to double eye springs on your trailer. You will need to have the slipper end hanger removed and have a new hanger welded on which allows the leaf spring to sit at the same height. Or you could…

view full answer...

Answer 11

Hey Caleb, it looks like the spring seat spacing for the 4-Leaf Double-Eye Spring for 2,000-lb Trailer Axles #E77SR is 13-1/3" so that's the spacing you'd need. What kind of trailer do you have? Any cool trips planned? Let me know if…

view full answer...

Answer 12

All of the products you listed will work together just fine. Keep in mind, if your current springs are not 26 inch springs, like the #e77SR you referenced, your hangers, #APS4, will not be in the exact same position as your current ones. When…

view full answer...

What Comes with Trailer Axle # e25GR

Product Page this Question was Asked From

Continue Researching