Replacement Seal for a Lippert 12088 Seal

Question

Question:

Looking for seal replacement for a 5200 lb Lippert axle seal. There have been problems recently with Lippert seals and wish to replace seals with a different brand. Lippert shows see link that the seal part 122088 for this axle is 2.25 ID and 3.376 OD, but does not show the width or thickness. These seals are either .375 or .438 in width, but cannot find any reference to what width is required or the specification on the Lippert seal 122088. Please let me know what seal would replace the Lippert 122088. Thanks.

asked by: Dale S

0

Expert Reply:

The Lippert Seal part number 122088 that you referenced has the same dimensions of 2.25 inner and 3.376 outer diameter as the Grease Seals # 10-36 that you referenced so they should work well for you.

Seal width should not matter, the only important dimensions are inner and outer diameter.

expert reply by: Jameson C

0

Answer 1

Thanks for the photo, and there isn't a specific vent cover that is going to attach to those plastic tabs, but so long as your Dexter vent is the standard size, measuring 14-1/4" x 14-1/4" at the roof opening, you can use a Fan-Tastic…

view full answer...

Answer 2

Hey Denny, based on the serial number of your roof vent lid the correct replacement would be the part #BVE0108-03 which is the same smoke color you have now.

view full answer...

Answer 3

Hey Jack, you'd probably want to go with the more universal style of RV roof vent cover part #MA00-933066 as this was designed to fit basically all roof vents. We don't have any that would fit directly to your Ventline mounting tabs at this…

view full answer...

Answer 4

I contacted Trimark in regards to a replacement part for the Trimark 030-0900. 030-0900 is actually a series number not a specific part number. To find the part number you will need to take the interior handle completely off the unit. On the back…

view full answer...

Answer 5

Hey Mike. The Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item #AL88338 do not fit the cab and chassis models of the 2017 Chevrolet Silverado 3500. Just the standard 2WD and 4WD with single rear wheels or…

view full answer...

Answer 6

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 7

We do indeed have replacement rubber grommets for a Furrion RV stove, and while they have a fancier name - "Trivet Support Bumper" - they are simply rubber grommets. The correct part is the following: - Replacement Trivet Support Bumper for…

view full answer...

Answer 8

Hi Charles, From what I could find, your DFMD35131 furnace is a 35,000 Btu that is 16-1/2" wide, 7" tall, and 20" deep. We do have a Dometic furnace that is the exact same size, but a 30,000 Btu unit, the Dometic RV Furnace #DMC38RR.…

view full answer...

Answer 9

I have attached a photo of a typical 4-way round connector with the pins labeled you can check out. The photo has both the trailer side and vehicle connectors labeled.

view full answer...

Answer 10

Hi Tanner; that is 100% correct. You can replace what you have now with the B&W Continuum Weight Distribution Head Assembly - 2-1/2" Shank #BW68FR if you do not want to use an adapter sleeve on your hitch. It would be great if you could just…

view full answer...

Answer 11

For a bearing kit for a Dexter 5200 axle we have the kit part #BK3-300 which comes with the correct bearings, races, and seal for your axle.

view full answer...

Answer 12

You mentioned grease seals for your 5,200 lb Lippert axle, which we do have, but since you also mentioned mating with bearing #25580, I'm not sure if you were possibly referring to the bearing races, so I'll just go ahead and give you both…

view full answer...

Replacement Seal for a Lippert 12088 Seal

Product Page this Question was Asked From

Continue Researching