Which Race is Correct for Trailer Hub Bearing LM67048

Question

Question:

You dont have the correct race for bearing LM67048,you show race L44610 when it should be LM67010 and bearing L68149 should be raceL68111. this is for hub 08-407-5.

asked by: Randy B

0

Expert Reply:

Hey Randy, I am not sure where you saw that the # LM67048 race is the # L44610 but it is for sure the # LM67010.

expert reply by: Jameson C

0

Answer 1

Sounds like you are looking for the trailer hub/drum part #8-407-5UC3-EZ which is for 4,400 lb axles, has the 6 bolt pattern wheel bolt pattern and also is the 8-407 you mentioned.

view full answer...

Answer 2

The spindles used on the 4400 axle are compatible with the #L67048 Inner bearing and #LM67010 race and the #L44649 Outer bearing and #L44610 race, along with the 10-19 grease seal, part #RG06-050. You'll want to confirm this by pulling one of the…

view full answer...

Answer 3

Hey Dan, as long as the outer bearing number you have now has an inner diameter of 1.25 inches like what comes with the #8-407-5UC3-EZ this will work for you. Do you have a 02475, 14125A, 15123, or a 387A? If so then it is same inner diameter and…

view full answer...

Answer 4

The #42 E-Z Lube Spindle w/ Flange #TRU37FR has a 1"-14 thread size. A replacement Trailer Spindle Nut #165686 is available if the treads are damaged on the castle nut.

view full answer...

Answer 5

Charles, for your camper with 4,400 lb axles you can use the Trailer Hub and Drum Assembly #8-407-5UC3-EZ. This hub and drum assembly will work with 4,400 lb axles, has a 6 on 5 1/2" bolt pattern, and includes the bearings, races, grease seal,…

view full answer...

Answer 6

Hey Juan, We do have just the nut retainer individually available as part #6-190. For the hub cap we do have a replacement hub cap with rubber plug available for a 2.72" hub bore diameter #TRU66FR. I wasn't sure if the 2.72 was the hub cap…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hey Patrick, thanks for the measurement. The Travel Door Latch for GE Appliances RV Refrigerator item #GE98FR has mounting holes 1-3/16" on center. It's designed for the 9.8 Cu. Ft. GE Appliances RV Refrigerator with Top Freezer item #GE58FR…

view full answer...

Which Race is Correct for Trailer Hub Bearing LM67048

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching