Dimensions of Fulton High-Performance 2-Speed Trailer Winch F142401

Question

Question:

I am interested in a Fulton F142401 2 speed winch. I need to know the overall dimensions of this winch to determine if it will fit my boat trailer. I need to know the following: 1 overall length of the winch from the forward end of the mounting base to the rear outer diameter of pulley. 2 the overall height of the winch from the bottom of the base to the top outer diameter of the pulley. 3 the width of the mounting base 4 the mounting base length See attached photo Thanks very much for your assistance

asked by: David P

0

Expert Reply:

Hey there David; thanks for the question and I was able to get the dimensions for you of the Fulton High-Performance 2-Speed Trailer Winch # F142401.

I added the dimensions of the # F142401 to the handy diagram you made (which I appreciate you sending), and the width of the mounting base is 5-3/4", the length of the mounting base is 6-7/8", the overall length is 8-1/2", and the overall height is 6-1/4" tall.

For a strap to go with the winch you can use part # FWS20HD0200.

expert reply by: Kyle S

0

Dimensions of Fulton Winch F142401
(click to enlarge)

Answer 1

Yes, you can change winch speeds with the Fulton winch part #F142401 with a load on the winch. There would be no need to not have a load on the winch for the gear selector to go between the fast and slow speeds.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Dimensions of Fulton High-Performance 2-Speed Trailer Winch F142401

Continue Researching