Brake Line Kit for Tandem Trailer with 10k Axles

Question

Question:

Hello good afternoon! I need a brake line kit for a 2 axle 10k dully trailer. Please!

asked by: Ronaldo D

0

Expert Reply:

The Redline Disc Brake Line kit part # 9579-2 that you referenced would work great with a 10k dually trailer like you have. It has a main feed line of 180 inches so you'd need to make sure that would be correct distance from back of actuator to the axles but aside from that this would come with everything standard that you would need.

expert reply by: Jameson C

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 3

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jordan! Based on your measurement you have a Lippert 1116 or 1716. If you want to confirm that feel free to send me the S/N on your pin box. The Gen-Y Nomad you were looking at is for the Rhino Box so that is not a fit. What you need is the Gen-Y…

view full answer...

Answer 7

Welcome back Adam. I can indeed tell you what gooseneck adapter you'll need for your 5th wheel trailer but I'll need the information on the sticker that's attached to the bracket above your current pin box. The white sticker should say…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 10

Hey Shane, the IOTA IDP-30 was a 30 amp distribution panel like the Progressive Dynamics 5000 Series AC/DC Distribution Panel #PD94MR that you referenced so this would be a great option to replace what you have. Did yours stop working?

view full answer...

Answer 11

Hey Roger, welcome back! I can give you the measurements for the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY33GR but I can't answer your question with the information I have available. If you look at the diagram attached…

view full answer...

Answer 12

Hey, Daniel. Thanks for your question. We do have a weight distribution hitch that would work for your trailer and still use chains. That hitch is the Blue Ox SwayPro #BXW0350. The tongue weight rating needed for this system to work is between…

view full answer...

Brake Line Kit for Tandem Trailer with 10k Axles

Product Page this Question was Asked From

Continue Researching