Does the Replacement Lock Cylinder for BOLT Toolbox Latch Work w/ Ford Keys?

Question

Question:

Will this fit a 2016 F250 SD key?

asked by: Lindell

0

Expert Reply:

Yes, it will so long as your Ford key looks like one in the picture below. The Replacement Lock Cylinder for BOLT Toolbox Latch item # BLT79FR only works with Bolt tool boxes. If not you will need item # BL7022698.

expert reply by: Jerred H

0

Ford Keys
(click to enlarge)

Answer 1

What you are wanting to do is likely possible with the Yakima #Y07138 OffGrid cargo basket. The OffGrid features crossbars that can be adjusted so that they're 24-34 inches, so if the mounts on the cargo box you're using can be adjusted so…

view full answer...

Answer 2

Congrats on your new purchase! Since your A.R.E DCU topper has the BOLT cylinders you'll want to use the Replacement Lock Cylinder item #BLT79FR. This cylinder will work with your 2018 F-350's key. To secure the cylinders in place you will…

view full answer...

Answer 3

What I would recommend is the Kuat Hitch Receiver Reducer Sleeve - 2-1/2" to 2" Hitch #KU93VR. This can be used with your current hitch reducer and will still allow your anti-rattle wedge to engage. However, it is likely you will need a new…

view full answer...

Answer 4

Hey robert, Your 2024 Ford F-350 should have the center cut key, but you can easily pop your key out of the FOB to confirm. We offer the following BOLT locks for this key style: BOLT Trailer Hitch Receiver Lock - 2", 2-1/2", and 3"…

view full answer...

Answer 5

A 2016 Chevy Colorado should have a center cut transponder key so you would need the Replacement Lock Cylinder for BOLT Toolbox Latch - Codes to Center Cut GM Key #BL7023480. This is just the replacement lock cylinder so if you're needing parts…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does the Replacement Lock Cylinder for BOLT Toolbox Latch Work w/ Ford Keys?

Product Page this Question was Asked From

Continue Researching