Will The MORryde RV Latch Extender Work With An RVLock Branded Entry Door Lock

Question

Question:

Does this work with RVlock?

asked by: Kim

0

Expert Reply:

Hi Kim,

Yes, the MORryde RV Door Latch Extender # MR22JR would be a compatible fit with an RVLock branded entry door lock. You'll just want to double check that you have enough clearance based on the steps listed below.

expert reply by: Kevin C

0

MORryde Latch Extender Clearance Requirements
(click to enlarge)

Answer 1

Hey Bob! The wall bracket on the MORryde Safe-T-Rail #MR54BR is 2-1/8" wide. Since you have 2-3/4" it will be able to fit in your available space. Are you upgrading your hand rail or did something happen to the original?

view full answer...

Answer 2

Hello Greg, Thanks for writing in, great question! The MORryde Add-A-Step for 23-1/2" Wide Step Above Treads #MR26MV will fit correctly even if the lower handrail kit is installed. The reason is that the handrail attaches to the side frame of…

view full answer...

Answer 3

The MORryde RV Door Latch Extender #MR22JR is a universal fit and will work with any paddle style latch with the proper clearances. Attached are some photos of those clearances along with a review video for you to check out. You can also find these…

view full answer...

Answer 4

For a 29-1/2 inch door opening the Lippert Solidstep Lift Assist you'd want is the part #LC733937.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Will The MORryde RV Latch Extender Work With An RVLock Branded Entry Door Lock

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching