What 2" Hitch Ball Will Fit The Curt TruTrack 2P Trailer Mounted Weight Distribution System # C67ZV?

Question

Question:

Can the ball be changed to a 2” ball instead of the 2-5/16”?

asked by: Jesús C

0

Expert Reply:

Yes, you are able to switch to the 2" Ball # A-90 on the Curt TruTrack 2P Trailer Mounted Weight Distribution System # C69JR. As Curt does not offer the hitch with a 2" ball you will have to change it out yourself or have it done at the shop which installs the hitch for you.

expert reply by: Bud M

0

Answer 1

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 2

Pretty much the only weight distribution systems that do not allow backing up while turning are the ones that have the bar style friction sway control pieces and with those you only would have to disengage the sway control bar and not the spring…

view full answer...

Answer 3

It sounds like your system may be overloaded. The first thing I would recommend is finding your actual tongue weight. Your Curt #C79JR (17600) has a tongue weight range of 800-1,000 lbs. If your tongue weight is around 1,000 lbs you're already at…

view full answer...

Answer 4

Hey Joe, yes the Curt TruTrack 2P part #C79JR does allow backing up as long as you are backing up mostly in a straight line. If you are going to get close to jackknifing the trailer at all though you would need to remove the springs bars. This is…

view full answer...

Answer 5

Ideally the loaded tongue weight of a trailer falls in the middle of the tongue weight range of the weight distribution system. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. So if your dry tongue weight…

view full answer...

Answer 6

Yes, you can use a 2 inch hitch ball with the Blue Ox SwayPro Weight Distribution w/ Sway Control #BLU54TR. There isn't a 2 inch hitch ball with the max 15,000 lb capacity though as 2 inch balls don't have the same rating as 2-5/16 inch…

view full answer...

Answer 7

I am sorry Mike but we do not sell custom fit fenders for your Forest River R-Pod. The absolute closest thing I could offer would be the CE Smith Single Axle Trailer Fender item #CE17100ATB. It measures 10" Wide x 32" long x 16" tall…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

This is a great choice Joe and thanks for reaching out! Weigh Safe True Tow Weight Distribution Hitch #WS49MR would be a good match for your setup. Since your Grand Design toy hauler will have a loaded tongue weight between 1,300 and 1,600 lbs, this…

view full answer...

Answer 12

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

What 2" Hitch Ball Will Fit The Curt TruTrack 2P Trailer Mounted Weight Distribution System # C67ZV?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching