Brake Controller Recommendation for 2024 Mercedes Sprinter 4500

Question

Question:

What brake controller would you recommend for my 2024 Mercedes Sprinter 4500? I prefer something smaller

asked by: Claude

0

Expert Reply:

The brake controller you are looking for for your 2024 Mercedes Sprinter 4500 would be the Redarc Tow Pro Liberty part # RED24FR with the install harness part # RED69FR. Since the vehicle doesn't have a great stoplight circuit signal you'd need the part # RM-751475 too.

expert reply by: Jameson C

0

Answer 1

Hey Dave, the install harness part #3063-P does fit to the green connector that is under your seat in your 2025 Mercedes Benz Sprinter 4500 and would work great with the P3 part #90195 which is widely considered to be the best controller around. I…

view full answer...

Answer 2

Hello Kent, thanks for reaching out. It is possible to use a Redarc brake controller in your 2024 Mercedes-Benz Sprinter 3500. The tow package on your printer includes a factory 7-way and brake controller port, correct? If so, a brake controller can…

view full answer...

Answer 3

Hey Nick, congrats on the new Sprinter. The Tekonsha Custom Harness item #3063-P does fit the green connector that is under your seat in your 2025 Mercedes Benz Sprinter 2500. It's compatible with the E98 prep package option as shown in the…

view full answer...

Answer 4

Hey Frank, look under the driver seat of your Grand Design Lineage built on a Sprinter chassis and let me know if you have the green connector. If so all you need is the Tekonsha P3 part #TK94HR and you'd have an easy to install brake controller…

view full answer...

Answer 5

I checked with Redarc and a few other brake controller manufacturers and they state that your 2024 Mercedes Sprinter 3500XD does not have an OEM brake controller install port under the dash like previous models so you would have to hardwire in the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Brake Controller Recommendation for 2024 Mercedes Sprinter 4500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching