Is there a Plug and Play Adapter to Install a Brake Controller on a 2023 Ford Expedition?

Question

Question:

Is there a plug in brake controller adapter for a 2023 Expedition? My suv came with the factory 7-way and I am looking to move over a P3 brake controller from my previous vehicle.

asked by: Kelly

0

Expert Reply:

Yes, there is! Since your 2023 Ford Expedition came with the factory 7-way you will have a brake controller port to use the Plug-In Wiring Adapter for Electric Brake Controllers item # 22292 to install the Prodigy P3 item # 90195 without cutting or splicing wires.

expert reply by: Jerred H

0

Answer 1

The wiring harness that you are seeking would be the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, and it is indeed part #22292. It will work with a host of brake controllers, including the popular Prodigy series, but must be a fit…

view full answer...

Answer 2

Hi David, the Tekonsha Plug-In Wiring Adapter #3034-P is different than the #22292. Neither is verified by Tekonsha to fit your 2024 Ford Ranger, though there has been anecdotal evidence the latter can work with some '24 Ranger models equipped…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Is there a Plug and Play Adapter to Install a Brake Controller on a 2023 Ford Expedition?

Continue Researching