How Many Sensors Can The TireMinder i10 TPMS Link To

Question

Question:

Is this system expendable to 14 sensors?

asked by: Pat G

0

Expert Reply:

The TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster # TM56FR is compatible with up to 20 sensors. Additional sensors can be purchased with part # TM-2Brass.

expert reply by: Kevin C

0

Answer 1

For the B and W Biker Bar part #BWMC2301 we have the replacement anchor plates part #BWMC2305 and the replacement anchor plates part #BWMC2300.

view full answer...

Answer 2

Your best solution will be the #LRB1. This D-ring anchor has a 4,000 lb working load limit, has mounting holes that are in line and has a continuously welded D-ring. I attached a review video for you to check out as well.

view full answer...

Answer 3

Using a piece of plywood between the aluminum will not hold up as well because the wood will start to weaken and will rot over time. The best way to install the trailer D-Ring Tie Down Mount, part #LRB1, to the aluminum floor in your car hauler would…

view full answer...

Answer 4

D-ring placement in your 27 foot trailer would be best determined by considering what will be loaded in the trailer. Without knowing more about what you plan on putting in the trailer it would be hard for me to give you an exact diagram. I believe…

view full answer...

Answer 5

The Brophy Recessed Trailer D-Ring Tie Down with Backing Plate #RR5K is not application-specific so its preferred method of installation will vary from trailer to trailer. The main factor is the thickness of the material to which it will be mounted.…

view full answer...

Answer 6

No, you can mount a recessed D-ring in any orientation you need and it will perform the same and have the same rating. I recommend #RR5K because it comes with a backing plate and hardware. It is rated for 5,000 pounds limited to the capacity of the…

view full answer...

Answer 7

If you look below the specs for the Trailer D-Ring Tie Down, #RR06, you will see that the lip is wider than the base . You would need to drill a hole that is 4-3/8 inches in diameter for the base to fit through and then use screws appropriate for the…

view full answer...

Answer 8

You will need to relocate your current booster to the back of your F-350. This will allow for it to have enough range to pick up the additional sensors that you are adding to the utility trailer. Longer trailers will require that the booster be…

view full answer...

Answer 9

The Replacement Anchor Plates for B&W Biker Bar Motorcycle Tie-Down Systems - Qty 2, #BWMC2305 are 4 inches by 6 inches and 1/4 inch thick. See the attached picture for further help of holes 3/4 and 1 inch on center from edges.

view full answer...

Answer 10

The Replacement Anchor Plates for B&W Biker Bar Motorcycle Tie-Down Systems part #BWMC2305 does not come with the mounting hardware needed for installation. As you mentioned you can pick them up at your local hardware store. I recommend using…

view full answer...

Answer 11

The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.

view full answer...

Answer 12

Thank you for providing that picture and measurement. Based on what you have there there is definitely enough room to install a weight distribution hitch. I recommend the Fastway e2 which will require placing the brackets 27-30" back along the…

view full answer...

How Many Sensors Can The TireMinder i10 TPMS Link To

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching