Dimensions Of Replacement Anchor Plates For B&W Biker Bar Motorcycle Tie-Down System

Question

Question:

Hello. Im planning to purchase steel mounting plates to install under my trailer floor to add support to the biker bar system. I would like to know the exact dimensions of these backing plates that are part of the biker bar setup. Thanks

asked by: Chris

0

Expert Reply:

The Replacement Anchor Plates for B&W Biker Bar Motorcycle Tie-Down Systems - Qty 2, # BWMC2305 are 4 inches by 6 inches and 1/4 inch thick. See the attached picture for further help of holes 3/4 and 1 inch on center from edges.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Replacement Anchor Plates for B&W Biker Bar Motorcycle Tie-Down Systems part #BWMC2305 come with 5/8"-2.5" hex bolts.

view full answer...

Answer 2

The backing plate BP05 will definitely make for a stronger tie down point, especially if you are not able to bolt the tie down ring to the trailer frame. If you can mount the ring through the frame at all four points, then you would not need a…

view full answer...

Answer 3

No, you can mount a recessed D-ring in any orientation you need and it will perform the same and have the same rating. I recommend #RR5K because it comes with a backing plate and hardware. It is rated for 5,000 pounds limited to the capacity of the…

view full answer...

Answer 4

Using a piece of plywood between the aluminum will not hold up as well because the wood will start to weaken and will rot over time. The best way to install the trailer D-Ring Tie Down Mount, part #LRB1, to the aluminum floor in your car hauler would…

view full answer...

Answer 5

Since you are planning on installing these Trailer D-Rings #RR06 in a plywood floor I would recommend you also get the Backing Plate #BP06 to offer better support than just the wood of your trailer floor. As far as the placement of them in your…

view full answer...

Answer 6

We sure do! The part number you're looking for is #BWMC2305, which provides a pair of anchor plates.

view full answer...

Answer 7

Your best solution will be the #LRB1. This D-ring anchor has a 4,000 lb working load limit, has mounting holes that are in line and has a continuously welded D-ring. I attached a review video for you to check out as well.

view full answer...

Answer 8

The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.

view full answer...

Answer 9

D-ring placement in your 27 foot trailer would be best determined by considering what will be loaded in the trailer. Without knowing more about what you plan on putting in the trailer it would be hard for me to give you an exact diagram. I believe…

view full answer...

Answer 10

Each model of the B&W Biker Bar Motorcycle Tie-Down System for Trailers will use two anchor plates #BWMC2305 to connect to. The anchors would be secured to the underbelly of the trailer making it hard to use in multiple locations, so you'd…

view full answer...

Answer 11

If you look below the specs for the Trailer D-Ring Tie Down, #RR06, you will see that the lip is wider than the base . You would need to drill a hole that is 4-3/8 inches in diameter for the base to fit through and then use screws appropriate for the…

view full answer...

Answer 12

The Brophy Recessed Trailer D-Ring Tie Down with Backing Plate #RR5K is not application-specific so its preferred method of installation will vary from trailer to trailer. The main factor is the thickness of the material to which it will be mounted.…

view full answer...

Dimensions Of Replacement Anchor Plates For B&W Biker Bar Motorcycle Tie-Down System

Product Page this Question was Asked From

Continue Researching