Can Steel Trailer Couplers Be Attached to an Aluminum Trailer?

Question

Question:

If someone is building me an aluminum trailer and I need to purchase a trailer coupler, does it matter if the coupler is made out of steel?

asked by: Mike R

0

Expert Reply:

You can safely use a Straight Tongue Coupler # DM13689-95 or A-Frame Coupler # DM13205-95 with your aluminum trailer frame. The zinc coating on these are not going to have any reaction with the aluminum frame.

Do be sure any channels use spacers in the frame to prevent it from collapsing when tightened.

expert reply by: Bud M

0

Answer 1

To get the Dexter Zinc-Plated, Leverlock Coupler #T4845000 in a higher weight rating you'll need to bump up to a hydraulic actuator like what we see with part #DX89FR which has a 7.5K weight rating. For an alternative standard coupler solution I…

view full answer...

Answer 2

Yes, you will be able to replace your stock coupler with the Demco 50-Degree A-Frame Trailer Coupler #DM13205-95 as long as you have a standard a-frame trailer. I attached a picture below of the dimensions below so you can see if it would work for…

view full answer...

Answer 3

Hey Daniel, I am really big fan of the latch system on the Demco eZ latch couplers like the part #DM13205-95. Unlike most of the current popular designs this stays easy to use over time and doesn't require a ton of finagling once its been out in…

view full answer...

Answer 4

The Demco EZ latch couplers like the part #DM13205-95 have a mechanism that will release when under tension like you are wanting and will allow the trailer to be jacked up and off the ball as well. This would be a great option.

view full answer...

Answer 5

The big difference between the two couplers you mentioned is that the Demco #DM13205-95 does not come with chain anchors and the part #DM16680-52 does.

view full answer...

Answer 6

As far as I know your 2008 Victory trailer has an A-frame on it. Assuming that is correct, and it is a 50 degree A-frame, I recommend one of the following: -Demco 50-Degree A-Frame Trailer Coupler #DM16680-52 (Bolt-On, Silver Powder Coat) -Demco…

view full answer...

Answer 7

It sounds like you're looking for a replacement a-frame coupler like #CA-5280-RB but in a silver-painted or zinc-plated finish. Please click on the link provided to see all bolt-on standard a-frame couplers for 2-5/16-inch balls. For the…

view full answer...

Answer 8

You can install Timbren Axle Less kits like the part #A35RS545 on aluminum frame trailers but it would be recommended to use like a rubber spacer/isolator to prevent galvanic corrosion. We don't have anything specific we can recommend but you…

view full answer...

Answer 9

In order to choose the correct replacement axle for a trailer you'll first want to start with the weight capacity. The weight capacity can be found on the axle tag in the center of the beam. Then, you'll need to measure the hub face (center…

view full answer...

Answer 10

Typically a trailer axle will have some camber in it - some bend - such that when it is not loaded the tops of the wheels bow outward slightly, with the outside edges of the tire treads making first contact with the ground. This allows that when the…

view full answer...

Answer 11

Aluminum trailer frames or bodies can cause grounding issues so I suggest using a separate ground wire that runs from the rear of the trailer up to the main ground post in the junction box like #38656. You can join the ground wires for the individual…

view full answer...

Answer 12

Based on the picture you attached of your motorcycle it does look like you will be able to jump in size to a 12 inch, possibly 13 inch tire and wheel combo. The important thing to maintain is at least 3 inches of clearance between the top of the tire…

view full answer...

Can Steel Trailer Couplers Be Attached to an Aluminum Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching