Recommended Trailair Pin Box to Replace a Lippert 1116 Pin Box

Question

Question:

I have a Moryde RPB72-1116, rated 19,000 lbs. Is the LC155943 a bolt in replacement? This will be fitted to a 2018 FL3731 Montana 5th wheel. Thank you for your time.

asked by: James R

0

Expert Reply:

Yes, it is! The MORryde item # MR87VR (our part number which is the RPB72-1116) and the Trailair Air Ride 5th Wheel Pin Box item # LC155943 both fit the Lippert 1116 bolt pattern. You will have no problem swapping these pin boxes out on your 2018 Keystone Montana.

expert reply by: Jerred H

0

Answer 1

While I do not have the actual component weight of the unit available to me, the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1116, #MR87VR, has a shipping weight of 165 lbs. So a few pounds less than that 165 to subtract…

view full answer...

Answer 2

Dimensions on most pin boxes are not the same, with the most important differential being the bolt pattern. Your pin box should have sticker on it either on the side or front that will have some serial numbers on it that we can use to identify the…

view full answer...

Answer 3

I contacted Lippert on your behalf. Your current LCI 1116 measures 17-7/16" from the bottom of pin to the top of pin box mounting. The Trailair Air Ride 5th Wheel Pin Box #LC155943 measures13-1/2 plus the pin at 3-3/8" or 16-7/8"…

view full answer...

Answer 4

I was able to physically measure the 5th Airborne Premium Fifth Wheel Air Ride Coupler #5AB-S500-700 for you and from the king pin center to the center of the airbag, the measurement is 6-1/2 inches. From the king pin center to the front pivot is…

view full answer...

Answer 5

It's possible you will be able to use the Trailair Air Ride 5th Wheel Pin Box #LC155943 on your 2014 Keystone Cougar High Country, but you will have to determine that pin box on your new Keystone is an 1116. Pin boxes are custom-fit, so it's…

view full answer...

Answer 6

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 7

Thank you for the photo of your Lippert pin box. You have their model 1116. I confirmed this with my contact at Lippert. The Trailair Air Ride 5th Wheel Pin Box #LC155943 that you referenced is a direct bolt-on replacement for the 1116. It comes…

view full answer...

Answer 8

Yes, the MORryde cushioned pin boxes can be used with the Andersen Ultimate gooseneck adapters like the part #AM3200 without requiring any adapters.

view full answer...

Answer 9

You will need the Kodiak Hydraulic Brake Hose #bh-3mfs90ff-1-5 on your 2022 Grand Design Solitude 310. This brake line has a male 90-degree fitting you will be able to attach at your brake assembly and a female assembly on the other end where you…

view full answer...

Answer 10

To lubricate the Curt Rota-Flex 5th Wheel Pin Box #LC328329 pivot points you'll just need a can of dry grease like part #RM-747 to grease the points without attracting dirt and debris that could gunk up the brackets. You'll just spray it on…

view full answer...

Answer 11

The cushion block on the Trailair Rota-Flex 5th Wheel Pin Box #LC328330 is not a replaceable part so I would first reach out to Lippert directly to see if this would qualify for a warranty replacement. If not you'd be looking at replacing the…

view full answer...

Answer 12

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Recommended Trailair Pin Box to Replace a Lippert 1116 Pin Box

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching