Replacement Spring Bar Retention Bracket for Reese Pro Round Bar Weight Distribution Hitch

Question

Question:

I am trying to find the part that goes to the bar that has the cotter key. to keep the bar from sliding off

asked by: Kenny

0

Expert Reply:

It sounds like you're looking for the spring bar retention bracket for your Reese Pro Round Bar Weight Distribution # RE94FR. The correct replacement is the Replacement Spring Bar Retention Bracket Kit # RP58498.

expert reply by: Robin H

0

Answer 1

Yes, the Replacement Spring Bar Retention Bracket Kit #RP58498 is the correct L-bracket for the 49913 part #RE44FR.

view full answer...

Answer 2

While Reese does not offer replacement spring bar retainers for their Weight Distribution Hitch 49912 #RE94FR, I do know some have used the Curt Spring Bar Retainer #17109 to replace them. These have a very similar design to hold the retainer pin in…

view full answer...

Answer 3

Yes, the Replacement Spring Bar Retention Bracket Kit #RP58498 can be used for your Reese Pro Round Bar Weight Distribution w Sway Control #RE44FR.

view full answer...

Answer 4

Hey Ron & Leslie, The Replacement Spring Bar Retention Bracket Kit #RP58498 you were looking at is a compatible replacement for your Reese Pro Round Bar Weight Distribution #RE34FR or you could also use part #RP25FR.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Welcome back Belinda! The Andersen Weight Distribution Hitch w Sway Control - 4" Drop/Rise - 16K GTW, 1.6K TW #AN33VR may work for towing your Grand Design Imagine XLS23LDE with your F-250. However, when we tested it a while back, we didn't…

view full answer...

Answer 9

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

Answer 10

Hi James! With your GVWR being 7,600 pounds, your loaded tongue weight should be around 760 pounds. With that said, I recommend going with the Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW…

view full answer...

Answer 11

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Answer 12

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Replacement Spring Bar Retention Bracket for Reese Pro Round Bar Weight Distribution Hitch

Featured Help Information

Miscellaneous Media

Continue Researching