Spindle Washer Needed For 2000 LB Axle With Standard Spindle

Question

Question:

I didnt realize this axle did not come with the spindle washer. What size washer do I need?

asked by: David

0

Expert Reply:

The washer that would fit the Dexter Trailer Axle Beam with Standard Spindles, part # T20BTR-7258, is part # SW1000. This has a 1 inch inside diameter.

I have attached a product review video for this washer.

expert reply by: Jeffrey L

0

Answer 1

I reached out to Dexter and they confirmed that you have a 2,200 lb axle. This means the correct bearing kit you need is part #BK1-150.

view full answer...

Answer 2

I called Dexter and they told me that your Dexter P-12 SLR SN: D5287869 axle has a 3,000 lb weight capacity. If you need any parts please let me know what they are and I would be happy to offer my recommendation.

view full answer...

Answer 3

We checked with Dexter and P-12 just indicates where the axle was made. With the serial number we could track down more info on your axle. However, in the mean time you could pretty easily get the bearing numbers off of your current bearings and then…

view full answer...

Answer 4

The tang washer included with the TruRyde Bearing Kit, #BK1-150, was designed to work with EZ Lube spindles. Easy lube spindles have a flattened portion on the threads (see photo) so they can use a tang washer to hold the nut in place. Non-EZ Lube…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Spindle Washer Needed For 2000 LB Axle With Standard Spindle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching