Replacement 5th Wheel Lead Landing Gear Leg for 2011 Keystone Cougar

Question

Question:

I have a 2011 Keystone Couger 5th The Lead Jack screw is seizing. Is the following the correct part # ? Replacement Lead Jack w/ Leg for Stromberg Carlson Landing Gear - Item # LG-179013

asked by: Henry F

0

Expert Reply:

You are correct that Lippert part # LC179013, their 5th Wheel RV Landing Gear Lead Leg, is the correct part to replace the damaged unit on your 2011 Keystone Cougar.

expert reply by: Adam R

0

Answer 1

Hey Peter, do you have a Lippert Ground Control leveling system on your Keystone Montana? If so, the part number you mentioned most closely corresponds with the replacement right rear leg part #LC428493. If instead this is a standard landing gear…

view full answer...

Answer 2

The difference in the repair kits for your VMC900R will be the Drive Shaft; a lead leg kit will have a different shaped shaft than the follow leg. The replacement Landing Gear Kit for Venture Follow Legs is #LC146060, while the Lead Leg repair kit is…

view full answer...

Answer 3

Yes, you can use Lippert lead leg #LC179013 and follower leg #LC179014 to replace the legs on your Fulton system. Many landing gear parts on newer 5th wheel trailers like yours are interchangeable.

view full answer...

Answer 4

To determine the correct landing gear repair kit for your trailer you will need to know the what make and model landing gears are installed. If you have a set of Lippert Components Venture landing gear, then the #LC146060 for the follow leg and…

view full answer...

Answer 5

Glad to hear how pleased you are with the Lippert landing legs #LC179013 and #LC179014! I spoke to my contact at Lippert and he recommended a white lithium grease like #L11354 for the zerk fitting for the gears and a silicone based lubricant on the…

view full answer...

Answer 6

We have Venture landing gear repair kits with part #LC146060 for the follow leg or part #LC146059 for the lead leg. To install the kits you'd want to take the legs off of the trailer.

view full answer...

Answer 7

In order to get the correct replacement drop leg you will need to know the manufacturer and model of your current landing gear because they do need to match in order to keep your Heartland Sundance level. For example, the Replacement Lead Jack w/…

view full answer...

Answer 8

Thanks for the pictures! Based on the part number of your motor it appears you have Venture landing gear. As such you will likely need follow leg rebuild kit #LC146060 or lead leg rebuild kit #LC146059 to fix your landing gear. Landing gear legs are…

view full answer...

Answer 9

I attached a picture that shows where the zerk fitting for greasing the Lippert landing gear part #LC179013 is, but if your landing gear does not have any fittings best bet would be to take off the top (if possible) and apply grease to the bevel…

view full answer...

Answer 10

Hello Keith, Yes, there are repair kits. I do not have a database that I can reference to see what was put on what camper. On my search I see that the Lippert Venture is the common lading gear on the 2003 Montana, for the follow leg (leg without the…

view full answer...

Answer 11

In order to find the correct replacement landing gear legs for your 2013 Keystone Laredo 335TG I would need you to take two quick measurements of your existing landing gear legs, the outer tube length and weld stop spacing. I have attached a photo to…

view full answer...

Answer 12

I spoke with my contact at Lippert who acquired Venture and he said that repair kit #LG-146059 is the correct kit for lead leg and then part #LC146060 for the follow leg.

view full answer...

Replacement 5th Wheel Lead Landing Gear Leg for 2011 Keystone Cougar

Product Page this Question was Asked From

Continue Researching