Does The HWT Aluminum Hi-Spec Series 6 Trailer Wheel # AM22651 Have a Maximum Pressure Rating?

Question

Question:

HWT #AM22651 is rated @ 2150lbs at what pressure.?

asked by: Brian P

1

Helpful Expert Reply:

The HWT Aluminum Hi-Spec Series 6 Trailer Wheel # AM22651 while having a maximum weight capacity of 2,150lbs, does not have a maximum pressure rating. The tire pressure rating is going to be supplied by the tire manufacturer. The Karrier ST225/75R15 Radial Trailer Tire Range C # AM10251 which fits the wheel you found has the same 2,150lb weight capacity. The manufacturer calls for a tire pressure of 50psi for this particular tire.

You always want to use the tire manufacturers pressure rating no mater if the capacity on the tire is higher like you get on the Load Range D # AM10256. This tire requires 65psi of pressure and can support up to 2,540lbs per tire. Since the wheel has a lighter capacity at 2,150lbs you still cannot exceed this capacity even with the higher capacity tire.

expert reply by: Bud M

1

Answer 1

The highest capacity we offer for an aluminum 15" diameter x 6" wide trailer wheel with 5 on 4-1/2" bolt pattern is 2,150 lbs like the Aluminum Hi-Spec Series 6 Trailer Wheel part #AM22651 which is what I recommend. This likely has the…

view full answer...

Answer 2

The Aluminum Hi-Spec Series 6 Trailer Wheel #AM22651 has a zero offset. This along with its 6 inch width gives it a backspacing of right at 3-1/2 inches. This is an excellent aluminum 15" wheel that features a weight capacity of 2,150 pounds and…

view full answer...

Answer 3

Hello Lindsey. I tried to do an internet search on the wheel information you sent, but could not find a definite answer. Most of the wheels that came up on my search is a 5 on 4 1/2 bolt pattern. I have included a print out so you can verify that is…

view full answer...

Answer 4

Torque specs for wheel lug nuts vary depending on several factors like stud size, wheel size and wheel material. The linked image provides a listing of commonly recommended torque values. The studs on your hubs #A35RS545E are 1/2-inch diameter and…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Does The HWT Aluminum Hi-Spec Series 6 Trailer Wheel # AM22651 Have a Maximum Pressure Rating?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching