Does The Peterson LumenX LED Trailer Tail Light M822R-7 Come With The Wiring?

Question

Question:

It is the right light but does it come with the wiring harness? Not seeing any picture with the harness attached.

asked by: Sebastian H

0

Expert Reply:

The Peterson LumenX LED Trailer Tail Light # M822R-7 does not include the wiring harness. They are sold separately. The correct wiring and plug for this light will be part # 431-491.

expert reply by: Jesse M

0

Answer 1

The Peterson LumenX LED Trailer Light #M826R-7 should replace your Peterson #435800 without issue. That being said, though they are the same diameter, the grommet may not be able to be reused. I suggest also getting #426-18 just to make sure you are…

view full answer...

Answer 2

I do have a solution, but the Peterson Thin Line #427400 doesn't have an LED equivalent. I could recommend a different light but that would require drilling new holes to get it mounted. What you can do instead is swap the bulbs to LED using the…

view full answer...

Answer 3

So what you have currently is our part #435800 which we have a replacement LED style light for with the part #M826R-7. For an install grommet you'll then want the part #426-18 and for a wiring harness part #431-491 and you'd be set.

view full answer...

Answer 4

The Replacement Lens part #A68RB that you referenced measures 3-1/2 inches long by 1-1/8 inches tall. If the lens you are looking to replace matches these dimensions then this would work for you. The part number for the light this lens is designed…

view full answer...

Answer 5

We don't offer a plug and play trailer harness that would plug directly into the Peterson #435800 trailer taillight. The lamp includes a 3 pin pigtail that would plug into the rear of the lamp which would wire directly into the trailer wiring. If…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Does The Peterson LumenX LED Trailer Tail Light M822R-7 Come With The Wiring?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching