What Torque Should Trailer Wheel 13 inch be Torqued to

Question

Question:

I just purchased from Etraile 2 Karrier ST175/80R13 trailer tires with 13 RIMS . What is the correct torque for the lug nuts? Thanks

asked by: Bob S

0

Expert Reply:

For 13 inch trailer wheel and tires like what you have you would want to torque the lug nuts to 75-85 ft lbs.

expert reply by: Jameson C

0

Answer 1

There is not really an exact relationship between tire size and lug nut torque specs. The relationship has more to do with the stud size and wheel construction. For example, if you were using this tire with 1/2" lug studs and steel wheels then…

view full answer...

Answer 2

A 13 inch trailer wheel is likely going to use 1/2 inch lug nuts. The torque spec is the same for a 13 inch wheel whether it is steel or an alloy wheel; 75 to 85 foot pounds. I have included a picture with a handy chart with torque values for you as…

view full answer...

Answer 3

There are a few advantages and disadvantages when deciding between bias ply #AM3S334 and radial tires #AM31994. With radial tires, some advantages would be: 1. Improved comfort. 2. Superior heat management and heat dissipation. 3. Excellent tire…

view full answer...

Answer 4

The Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel #AM31994 will work if the 1,610 lbs at 65 psi weight rating (per tire) is enough for your boat and trailer. This gives you a total weight capacity of 6,440 lbs. If you need a…

view full answer...

Answer 5

It would be odd for the 4-1/4 inch measurement to be accurate. I've attached an article on measuring bolt pattern for you to confirm your bolt pattern before ordering. If you do end up with the same measurements, you may want to consider changing…

view full answer...

Answer 6

The Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D #AM31994 does not have specific torque specs. The torque values will be based on the lug nuts and wheel size. For your wheel size and material, you…

view full answer...

Answer 7

For most boat trailers, it's okay to use powder coated steel wheels but this is mostly for freshwater. I am not saying you can't use powder coated steel wheels on a boat trailer in saltwater but it's really not the best option for…

view full answer...

Answer 8

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 9

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 10

The grease seal that comes in the Bearing Kit #BK1-150 is part #10-9 and is a TruRyde product, yes. This seal has a 1.500" ID and a 1.987" OD and is typically found on 1-1/16" spindles like what you mentioned. The part 471750 is a…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What Torque Should Trailer Wheel 13 inch be Torqued to

Product Page this Question was Asked From

Continue Researching