Dimensions of Roadmaster Tow Dolly Ramp Wear Strip

Question

Question:

Will the Roadmaster Tow Dolly Ramp Wear Strip fit my MASTER TOW TOW DOLLY?

asked by: George G

0

Expert Reply:

The Roadmaster Tow Dolly Ramp Wear Strip and Spacer Plate Replacement Kit # RM-2000-25 was designed specifically for the Roadmaster Tow Dolly so while I can't confirm if it will fit your Master Tow Tow Dolly, I can verify some of the specs which you can also see in the linked photo:

- Width 8-1/4"
- Length 16"
- Bolt Hole Centers 13-15/16"
- Bolt Hole Diameter 3/8"

expert reply by: Jon G

0

Dimensions of Roadmaster Tow Dolly Ramp Wear Strip
(click to enlarge)

Answer 1

The wear plate in the Roadmaster #RM-2000-25 is 16" long x 8" tall and the holes are spaced 14-1/2" apart. The spacer plate is 4" long x 3" tall and 1/4" thick.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Dimensions of Roadmaster Tow Dolly Ramp Wear Strip

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching