Will Draw-Tite Hitch and Tekonsha Wiring Harness Fit 2007 Honda Odyssey

Question

Question:

I have a 2007 Honda Odyssey’s can you please confirm these parts ware compatible with my vehicle- 752701 118438 And the braseo controller necessary ETBC7 Thanks

asked by: Guzman W

0

Expert Reply:

Both the Draw-Tite Max-Frame Trailer Hitch Receiver # 75270 and the Tekonsha # 118438 will fit your 2007 Honda Odyssey. The # ETBC7 is a universal installation so it will also fit. This will upgrade the Tekonsha wiring harness from a 4-way to a 7-way so you can use a brake controller.

The Redarc Tow-Pro Liberty Brake Controller # RED24FR you were looking at is my favorite brake controller and one I highly recommend. Installation of the brake controller will also require the Universal Wiring Harness # RED69FR.

In order to complete your setup you will also need a ball mount. Check out the etrailer Ball Mount Kit # 989900. This kit comes with two ball mounts, one with a 3/4" rise or 2" drop and the other with a 2-3/4" rise or 4" drop. It also includes a 1-7/8" and 2" ball, as well as a ball mount bag to store everything in.

I have attached some installation videos below for your reference.

expert reply by: Robin H

0

Answer 1

I attached an install video for the brake controller install kit part #ETBC7 on a similar 2014 Honda Odyssey as your 2015 model. You can use this as a guide for installing the Redarc Tow Pro Part #RED44FR that you referenced. The brake controller in…

view full answer...

Answer 2

There aren't any plug-in adapters for your 2023 Nissan Pathfinder unfortunately, so you'd have to use the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers #RED69FR that comes with the brake controller. You could also use…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

We have two rear suspension alternatives for a 2011 Odyssey. The #THROD2 from Timbren which would replace the factory bump stop in the coil spring or the #AL60815 air helper spring from Air Lift which installs inside the coil spring as well, but…

view full answer...

Answer 5

Best solution we have would be rear suspension enhancement for your 2017 Honda Odyssey. We have the Air Lift kit part #AL60815 which basically allows you to add air pressure to increase the suspension support as needed. Or we have the Timbren kit…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The primary difference is a matter of numbers. When installed, the Draw-Tite Class III #76025 will sit so the inside top edge of the receiver tube sits about 13 inches above the ground, and the receiver tube will sit under the bumper so that the…

view full answer...

Answer 8

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75270 is the replacement for the Hidden Hitch 87479 you mentioned. This hitch is confirmed to fit 1999 through 2017 Honda Odyssey model years. I've attached an…

view full answer...

Answer 9

From what little I was able to learn about the VelociRAX 5 bike rack on their website, the rack is compatible with a 2 inch hitch that has a tongue weight capacity of at least 500 lbs, and the Draw-Tite #75270 Class III hitch meets both those…

view full answer...

Answer 10

Curt decided not to design hitch #C13068 to account for those welded on pieces you referenced in order to maximize the size of the side hitch brackets. As to why they chose to go with a 5 bolt design I can't say. The Draw-Tite hitch #75270 sounds…

view full answer...

Answer 11

For a hitch with a high enough tongue weight capacity you will need the Draw-Tite Max-Frame Trailer Hitch Receiver #75270. Although the #e98862 does have a max tongue weight of 500 lbs with weight distribution, this would require a weight…

view full answer...

Answer 12

For your 2017 Honda Odyssey the Draw Tite hitch part #76025 is a great option to tow with. It has a concealed crosstube too so that it's not overly visible. You will need to start with a 4-way (if you do not have one). For that you would want the…

view full answer...

Will Draw-Tite Hitch and Tekonsha Wiring Harness Fit 2007 Honda Odyssey

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching