Info Needed to Pick Out Replacement Trailer Hub

Question

Question:

I am looking for a vortex hub assembly for my 2007 ranger z20. Ranger part number is 205788. Do you have them?

asked by: Chad

0

Expert Reply:

I can not find any info on that hub part number so I am not able to help determine what would be the correct replacement. If you can get me the trailer axle capacity and the wheel bolt pattern that would be all we'd need to pick out correct replacement. For example, the Dexter hub/drum part # 8-247-50UC3-EZ is for the very common 3,500 lb axle and has a 5 on 4-1/2 inch bolt pattern.

expert reply by: Jameson C

0

Answer 1

Based on my research, the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will be a perfect replacement for your Shelby 5756A trailer jack. This jack will allow you to use the existing snap ring jack mount on your trailer for installation.…

view full answer...

Answer 2

It really comes down to the weight capacity for your axle on your 2005 Ranger boat trailer. As we do not carry any spindles which have a 1-3/8" inner bearing and 11/16" outer bearing. Here are the more common size spindles used today on…

view full answer...

Answer 3

The 171255UC seal is the same as the Dexter 010-11088/K71-G01-80. We have that same seal available as the Grease Seal Kit- Triple Lip - Inner Diameter 1.719" - Outer Diameter: 2.565" - Qty 2 #DX49CR.

view full answer...

Answer 4

The 11033L hub shown in your photo was manufactured by Tie Down Engineering, or TDE. What you have there is a hub for a standard 3500 lb axle which has a 5 on 4-1/2 inch bolt pattern. For an idler hub, I'd recommend the galvanized…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

Hey Matt, welcome back! The Rock Tamers Adjustable Mud Flap #RT67VR is designed for a 2" receiver. The factory hitch on your 2024 GMC Sierra 3500 is 2-1/2" so you need the #ERT00110 instead. If you want the option with the screen that would…

view full answer...

Answer 9

Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…

view full answer...

Answer 10

Hey Bill! We've got a couple of really good ball mounts that fit a 3" receiver and will work with the Adjustable Mud Flap System item #RT77VR, you just purchased. I recommend the following ball mounts: 4-1/2" Drop, 4" Rise -…

view full answer...

Answer 11

Welcome back Bill! For your 2020 Ford F-350 Dually, the Rock Tamers Adjustable Mud Flap System with Rock Screen item #RT77VR is going to be the correct one if you went with the upgraded 3" hitch receiver Ford offered and use 3" ball mounts.…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Info Needed to Pick Out Replacement Trailer Hub

Product Page this Question was Asked From

Continue Researching