Width of Timbren Trailer Suspension Enhancement System for Underslung Axles Mounting Brackets

Question

Question:

Can you please tell me the width of the bracket longest side of the Timbren T92MR marked in attached photo. Thank you

asked by: Dan S

0

Expert Reply:

The width of the Timbren Trailer Suspension Enhancement System for Underslung Axles # T92MR mounting brackets is 4-1/2". I've attached a photo for your reference.

expert reply by: Jon G

0

Width of Timbren Trailer Suspension Enhancement System for Underslung Axles Mounting Brackets
(click to enlarge)

Answer 1

The Timbren Trailer Suspension Enhancement System for Underslung Axles #T92MR is 5-1/4" tall. Timbren recommends The spring be in constant contact with the frame at all times. So ideally you will want exactly 5-1/4" from your axle tube to…

view full answer...

Answer 2

The Timbren Trailer Suspension Enhancement System #TTRA1702 is 2-3/4" tall with no load on the spring. This particular system is designed to mount to the frame with the included bracket(see image) and when the suspension compresses the axle will…

view full answer...

Answer 3

The Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs #TTRA1702 will be a great help in reducing body roll and helping dampen the bounce. Based on your measurements this will immediately take on load and stabilizing while…

view full answer...

Answer 4

As the max working load of your 48" x 96" Harbor Freight Haul Master utility trailer is 1,720 pounds, the Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs #TTRA1702 will have no issue working with it. However,…

view full answer...

Answer 5

Yes, Scott, that’s exactly what it’s made for. All three Prime Guard formulas are non-toxic and won’t damage plumbing if left in place for the off-season. Just remember to flush with fresh water before first use. That said, I strongly recommend going…

view full answer...

Answer 6

Absolutely! All three Prime Guard formulas - #PG56ZR, #PG36ZR, and #PG96ZR - are safe for both RV and marine systems. They’re safe for potable water lines, pumps, and even outboard engine water jackets. Just be sure to flush thoroughly in spring, and…

view full answer...

Answer 7

Hey Henry, the weight capacity of the Timbren suspension system part #T92MR is 5k for the axle or in other words for both of them combined. You should note this doesn't increase the towing capacity of your vehicle by this much weight as instead…

view full answer...

Answer 8

Hey Les, that's because we don't have one unfortunately. The only 40 lb tank cover we have is the Adco RV Propane Tank Cover for Dual 40-lb Tanks #290-2714 which is a soft cover. If there is anything else I can do to help you though, please…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Width of Timbren Trailer Suspension Enhancement System for Underslung Axles Mounting Brackets

Featured Help Information

Miscellaneous Media

Continue Researching