Recommended Propane Cover for Dual 40 lb Tanks

Question

Question:

I am looking for a hard cover for dual LP gas tanks, 40 lb. I cannot locate that in your store. Please advise.

asked by: Les M

0

Expert Reply:

Hey Les, that's because we don't have one unfortunately. The only 40 lb tank cover we have is the Adco RV Propane Tank Cover for Dual 40-lb Tanks # 290-2714 which is a soft cover.

If there is anything else I can do to help you though, please feel free to drop a comment and let me know.

expert reply by: Bryce D

0

Lazer S.

10/27/2025

Hey Les, did the Adco soft cover for your dual 40‑lb tanks end up working for your setup? Knowing how it fit could help others looking for a similar option.

Answer 1

Hey Eric, thanks for reaching out! Ultimately, I'll need more specific info on your trailer (the GVWR would be best), but I can still help you figure out how to choose a weight distribution hitch (WDH). What you'll need to look for is the max…

view full answer...

Answer 2

Have you tried reprogramming the remote? For programming a Fan-Tastic roof vent remote like part #FV9068-09 which is what your 7350 fan part #FV807350 uses what you need to do is hold your remote 12 inches away from the fan while holding both arrows.…

view full answer...

Answer 3

Hey Jeff, yes you can use the Flair-It High Pressure Hose #FL57FR with PEX crimp rings like you mentioned.

view full answer...

Answer 4

If the lift motor will no longer operate with the controller but does when you apply direct 12 volt power then that tells me there is an issues with the control board. The only way to replace the control board on the Fan-Tastic Vent Roof Vent part…

view full answer...

Answer 5

Hey Claudia, I checked with Curt just now and confirmed that their hitch part #C64DR does fit all models of the 2026 Toyota Corolla Cross which includes the hybrid models so it would work great for you. We also had customers with similar hybrid…

view full answer...

Answer 6

Thanks for your question, James. Both the etrailer #e98948 and Demco #DM9519336 base plates will have a very similar, low-profile look once they’re installed, so neither one really stands out more than the other. They’re both custom-fit for your…

view full answer...

Answer 7

Hey Michael, congrats on the new SUV. The EcoHitch item #EH87CR does not require you to remove the rear bumper assembly when installing. It does require some slight fascia trimming though. You'll have to remove a 2-3/4” deep and 4-1/2” wide…

view full answer...

Answer 8

Hey Karl, thanks for reaching out. Yes, you can get a replacement for the 7-way socket that came with the #ETBC7L kit. For that you'll need the following: - Buyers Products Trailer Connector Adapter - 4-Way to 7-Way RV and 4-Way Flat #337TC1474P…

view full answer...

Answer 9

Hi Chris! The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e83ZR will indeed fit your 2026 Subaru Forester Wilderness edition. This will bolt right on, though there is an underbody panel that will need to…

view full answer...

Answer 10

If the bike rack initially comes with a threaded hitch pin like the Malone #MPG2149 or the Curt #C18085 then a locking hitch pin like part #C23519 that you referenced won't actually fit. I do have some alternatives though that you can check out.…

view full answer...

Answer 11

Will, you're going to have to find out if the d-rings on your bumper are rated to be flat towed. If they can you can just use an adapter and a set of tow bars and you'd good. Otherwise, you're going to need to install a standard base…

view full answer...

Answer 12

Hey Henry, the weight capacity of the Timbren suspension system part #T92MR is 5k for the axle or in other words for both of them combined. You should note this doesn't increase the towing capacity of your vehicle by this much weight as instead…

view full answer...

Recommended Propane Cover for Dual 40 lb Tanks

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching