Recommended Wiring Harness to Install a Redarc Tow-Pro Liberty in a 2023 Ford Ranger

Question

Question:

How do I install the Redarc Tow Pro Liberty in my 2023 Ford Ranger?

asked by: Perry

0

Expert Reply:

To install a Redarc Tow-Pro Liberty Brake Controller item # RED24FR in your 2023 Ford Ranger you will want to use the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item # RED69FR. The 2023 Ranger's do not have a port for a plug in adapter so you will need to manually wire into your truck.

expert reply by: Jerred H

0

Answer 1

Hey Ken! The correct wiring harness depends on whether or not you have the brake controller port/plug. Some models did not include the plug so you will have to check your 2025 Ranger and see. There should be four wires coming out of a large wire…

view full answer...

Answer 2

Hello Fred, thanks for reaching out. We do have brake controllers that can be used on your 2025 Ford Ranger, but I am sorry to say we do not have anything with a custom pigtail for the factory under dash EBC plug. All of the options we have at this…

view full answer...

Answer 3

Hey, Stephen! We got just what you need. Since you don't have a tow package, I'm not sure if you have a hitch on your 2025 Ford Ranger so I'll include one just in case. Draw-Tite Max-Frame Trailer Hitch Receiver Part #DT35PR Curt…

view full answer...

Answer 4

Hi Charles; the Redarc Tow-Pro Liberty Brake Controller #RED24FR can be added to your 2022 Ford Ranger XL with the factory tow package. It doesn't look like the Ranger has a factory brake controller port, even with the factory 7-way, so you will…

view full answer...

Answer 5

Your 2022 Ford Ranger doesn't have a brake controller wiring port under the dash and instead has 4 wires that are sticking out of the large wire harness that goes through the diriver's side firewall left of the brake pedal. They have shrink…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Using the cut off wiring harness you have for the P3 part #90195 you will wire it to the brake controller wiring of your 2023 Ford Ranger which is sticking out of the large wire harness that goes through the driver's side firewall, left of the…

view full answer...

Answer 12

Hi Jeff! I have everything you need to get your 2025 Ford Ranger Raptor set up for flat towing below. I did go with the heavier tow bar as your curb weight (right about 5,400 pounds) was getting a little too close to the capacity of the smaller…

view full answer...

Recommended Wiring Harness to Install a Redarc Tow-Pro Liberty in a 2023 Ford Ranger

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching