Which Redarc Tow-Pro Liberty Wiring Harness Fits 2025 Ford Ranger XLT

Question

Question:

What red arc brake controller and wire harness for 2025 ranger xlt with minimal tow package and factory wiring plug connection, was going to order red24fr

asked by: Ken M

0

Expert Reply:

Hey Ken! The correct wiring harness depends on whether or not you have the brake controller port/plug. Some models did not include the plug so you will have to check your 2025 Ranger and see. There should be four wires coming out of a large wire harness by the driver side firewall, left of the brake pedal, which can be wired to the brake controller wires.

If you have the brake controller port you can use the # 331-TPH-007 to install the Tow-Pro Liberty # RED24FR. If you only have the wires without the plug, you need the # RED69FR which is the universal wiring harness for a splice-in installation. These also come bundled as the # RED67CR with the custom wiring harness and # RED52VR with the universal.

What are you towing with the Ranger?

expert reply by: Robin H

0

Redarc Tow-Pro Liberty
(click to enlarge)

Ken M.

4/30/2026

I’ll be towing a Jayco jay feather 20 ft. I received my order today. I ordered the RED 24 FR, I received a EBRH-ACCNA, are these units the same?, did they send me the correct controller, it’s a bit confusing. I also received the TPH-007 harness.

Robin H.

5/1/2026

@KenM the # RED24FR is our part number, Redarc uses EBRH-ACCNA, they are the same thing. We actually have it on the product page sitting below the description and specs. TPH-007 is the same as # 331-TPH-007 but that one is a little more obvious. Assuming you have the factory port you're all set for installation.

Ken M.

5/1/2026

@Robin , installed and wired up today, a little bit of a challenge but found a location underneath the drivers side dash near where it needs to plug into. Zipped tied to a metal support frame. Mounted control knob below truck light switch. Hooked up to trailer and all lights are working. Everything seems to be working, all components installed easily and will go out tomorrow to calibrate brakes. Thanks for all your help and support.

Robin H.

5/2/2026

@KenM you're welcome! Once you get it calibrated you’ll be all set and ready to tow your Jay Feather. Be safe out there.

Answer 1

Hello Fred, thanks for reaching out. We do have brake controllers that can be used on your 2025 Ford Ranger, but I am sorry to say we do not have anything with a custom pigtail for the factory under dash EBC plug. All of the options we have at this…

view full answer...

Answer 2

Using the cut off wiring harness you have for the P3 part #90195 you will wire it to the brake controller wiring of your 2023 Ford Ranger which is sticking out of the large wire harness that goes through the driver's side firewall, left of the…

view full answer...

Answer 3

The Tekonsha Prodigy RF Wireless Trailer Brake Controller #TK94FR must be mounted to the trailer in a certain way in order to function correctly. It cannot be connected to the tow vehicle. A better option for you is the new Curt Echo Wireless Trailer…

view full answer...

Answer 4

Hey, Stephen! We got just what you need. Since you don't have a tow package, I'm not sure if you have a hitch on your 2025 Ford Ranger so I'll include one just in case. Draw-Tite Max-Frame Trailer Hitch Receiver Part #DT35PR Curt…

view full answer...

Answer 5

Your 2022 Ford Ranger doesn't have a brake controller wiring port under the dash and instead has 4 wires that are sticking out of the large wire harness that goes through the diriver's side firewall left of the brake pedal. They have shrink…

view full answer...

Answer 6

To install a Redarc Tow-Pro Liberty Brake Controller item #RED24FR in your 2023 Ford Ranger you will want to use the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED69FR. The 2023 Ranger's do not have a port for a…

view full answer...

Answer 7

Hi Charles; the Redarc Tow-Pro Liberty Brake Controller #RED24FR can be added to your 2022 Ford Ranger XL with the factory tow package. It doesn't look like the Ranger has a factory brake controller port, even with the factory 7-way, so you will…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Which Redarc Tow-Pro Liberty Wiring Harness Fits 2025 Ford Ranger XLT

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching