Replacement Pull Pin for Pro Series Round Swivel Jack # PS1401480303

Question

Question:

Is there a replacement part for the 9/16inch pull pin for this jack?

asked by: Fred K

0

Expert Reply:

To replace the 9/16 inch pull pin for your Pro Series Round Swivel Jack # PS1401480303 you can use the Replacement Pull Pin # BD500243. This includes the pin, chain, and drive screw.

expert reply by: Chris R

0

Answer 1

First, you are going to need a key for the old locks. The key is needed to depress the tumblers in the locks you have. Otherwise you will not be able to get them out. What is the number on the face of the locks you have? With the key inserted you…

view full answer...

Answer 2

The outer diameter of the pipe mount that comes with the Pro Series Round, Pipe-Mount Swivel Jack part #PS1401480303 is 2". It uses a 5/8" diameter pin.

view full answer...

Answer 3

You can place the pin on the Square Pipe Mount Swivel Jack w/ Footplate #TJDP-5000-FLB either way when it is holding weight. The weight of the trailer will be bearing down on that pipe mount bracket while the pin just keeps the trailer jack in place.…

view full answer...

Answer 4

The Square Pipe Mount Swivel Jack #TJDP-7000-B uses the Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks #TJP-OP58 which has a 2 inch inner diameter and 2-1/4 inch outer diameter. In the video the description is of the weld-on pipe mount…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 9

It sure does Steve! Our 3,500 lbs etrailer Electric Trailer Jack w/ Tongue Weight Scale item #e43KV also comes in a 5,000 lbs capacity. We have two different options depending on how you want to power it that I have listed below: Wired to Trailer -…

view full answer...

Answer 10

It sure will Jim but it will take some modification! The Space Dock 2" Receiver Adapter for Torklift Palomino Landing Pad Bumper item #TLA7900 requires a genuine Palomino Landing Pad bumper. The shaft may need to be shortened to seat properly.…

view full answer...

Answer 11

Hey Seth, The etrailer Electric Trailer Jack w/ 7-Way - Drop Leg - A-Frame - 18" Lift - 5K #e74GV may work on your 2015 Ford F-250, but there's a high chance that it won't straight out of the box. On 2015 and newer Ford trucks with a…

view full answer...

Answer 12

Hey Will! The square tube on the Bigfoot Hydraulic Trailer Jack #BF94FR is 4" x 4". What kind of trailer do you have?

view full answer...

Replacement Pull Pin for Pro Series Round Swivel Jack # PS1401480303

Continue Researching