Outer Pipe Mount Diameter for Pro Series Round, Pipe-Mount Swivel Jack

Question

Question:

Can you give me the o.d. of the mounting tube inner of this trailer jack? PS1401480303

asked by: Samhart

0

Expert Reply:

The outer diameter of the pipe mount that comes with the Pro Series Round, Pipe-Mount Swivel Jack part # PS1401480303 is 2". It uses a 5/8" diameter pin.

expert reply by: Conner L

0

Answer 1

First, you are going to need a key for the old locks. The key is needed to depress the tumblers in the locks you have. Otherwise you will not be able to get them out. What is the number on the face of the locks you have? With the key inserted you…

view full answer...

Answer 2

You can place the pin on the Square Pipe Mount Swivel Jack w/ Footplate #TJDP-5000-FLB either way when it is holding weight. The weight of the trailer will be bearing down on that pipe mount bracket while the pin just keeps the trailer jack in place.…

view full answer...

Answer 3

To replace the 9/16 inch pull pin for your Pro Series Round Swivel Jack #PS1401480303 you can use the Replacement Pull Pin #BD500243. This includes the pin, chain, and drive screw.

view full answer...

Answer 4

The Square Pipe Mount Swivel Jack #TJDP-7000-B uses the Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks #TJP-OP58 which has a 2 inch inner diameter and 2-1/4 inch outer diameter. In the video the description is of the weld-on pipe mount…

view full answer...

Answer 5

Hey Rich, the replacement Brophy wheel part #1206 was not designed for use on a trailer so it does not have a stated weight capacity when used on a trailer. Basically it is to help move around the Brophy camper jacks part #CX74.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Lars, welcome back! I can indeed confirm that the Furrion Variable Speed Chill Cube air conditioner with a heat pump is indeed really happening. They are currently available for order (02/04/26) and will be shipped out towards the middle of next…

view full answer...

Outer Pipe Mount Diameter for Pro Series Round, Pipe-Mount Swivel Jack

Continue Researching