Replacement Hub/Drum for Triton Axle 08353

Question

Question:

Have a Triton XL jet ski trailer that is needing a new hub with bearings and auto grease end cap. Have a part number of the axel #08353 is that enough info or you need more?

asked by: John

0

Expert Reply:

With the info you listed I was able to determine that you have a 5 lug 2,000 lb capacity hub no so for a replacement you would want the # AKIHUB-545-2-G-EZ-2K that you referernced. This comes with bearings and an ez lube cap as well.

expert reply by: Jameson C

0

Answer 1

Overpacking the trailer hub with grease is the number one reason for grease seal failure. For a boat trailer I would recommend re-packing the hubs by hand with grease once per season and you'd be fine. I don't like recommending people use…

view full answer...

Answer 2

In order to find the correct hubs/drums for a trailer you'll need to know either the axle capacity, bearings numbers, or spindle dimensions. We can't look any of this up for any one particular trailer as there is simply no database of this…

view full answer...

Answer 3

Hello Chris, Yes, we do have a hub that will work for you the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased #CE13315, or cast iron #CE13311. This hub has both inner and outer bearing L44649, and…

view full answer...

Answer 4

According to Triton your trailer uses their 08353 axle with 11228 bearings which are the same as the #L44643. For a marine-grade replacement hub I recommend the #AKIHUB-545-2-G-1K. This comes with everything including the bearings and grease seal. If…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 7

Hi Steven; take a look at the diagram below. Since your springs wear out over time it is best to use measurement D and E and match what is on your trailer. For the 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles #e69SR D is 12"…

view full answer...

Answer 8

The owner's manual for the Reliable axle on your Triton PWC trailer indicates that the bearing used on the axle of your weight rating is #L44643. This part serves as both inner and outer bearing according to the manual, which I linked for you. We…

view full answer...

Answer 9

We have a 2,000 lb axle that has an overall length of 72 inches from hub face to hub face and has a spring center dimension of 58 inches like you need, part #T20BTR-EZ-7258. Check out the review video I attached for more info. We don't have a…

view full answer...

Answer 10

Yes, you can use 4-leaf springs in place of 3 leaf springs. The extra height of an additional leaf is minimal and won't really affect anything on the trailer. Provided that the springs used are replaced in pairs and not just one side of the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Hub/Drum for Triton Axle 08353

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching