Will I Lose the Tow Hooks When Installing a Front Hitch on a 2022 GMC Sierra 2500?

Question

Question:

will i lose the tow hooks on my 2022 GMC 2500 if I install the Curtis front hitch?

asked by: Allen N

0

Expert Reply:

No, you will not. The Curt Front Hitch item # C52NR mounts below the tow hooks when installed on your 2022 GMC Sierra 2500 so you will retain them.

I have linked an installation video below so you can see what this hitch looks like once installed.

expert reply by: Jerred H

0

Answer 1

The bolt and washer that are inserted into the frame will act as the wrench on the top part of the bolt. The bolt itself is a carriage bolt which has a square notch in the bottom of the head and the washer has a slightly larger square notch in it for…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Hey Kenny, welcome back! The reason for that note is because all of the new systems since 2025 use R32 refrigerant due to EPA regulations. Any 2024 and older systems use R410A and their parts are not compatible with the R32 units. It doesn't mean…

view full answer...

Answer 5

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Answer 6

Hello Dustin, To mount the TecNiq Mini Side Marker Light - Amber - 3/4" - Grommet Mount - 9" Wire #TN22XR, you’ll need to drill a 3/4-inch diameter hole. The rubber grommet is designed to press-fit into this standard hole size, allowing the…

view full answer...

Answer 7

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 8

Hi Randy; that part number corresponds with the OEM Chill Cube. At this time, there are no heat strips available from Furrion. They have said they are developing one, but it has been over a year with no word on an ETA. The only option for heat on a…

view full answer...

Answer 9

Hello Thomas, I can definitely help with that. For your 2003 Sierra 3500HD long bed dually 4x4 with full length running boards you will need the following: - TorkLift Tie Downs - Custom Frame Mount - Front and Rear #TL56VV This comes with both the…

view full answer...

Answer 10

Hey Dean, the Detail K2 Elite Snowplow part #K2AVAL8219ELT that you referenced comes with all of the electrical components it will need to install. It wires to the vehicle battery as well as comes with a wired switch that you would run to the cab of…

view full answer...

Answer 11

Hey Mark, so the Curt hitch part #C15302 basically is strong enough without attaching to the bumper so it wasn't designed into it. Curt is very thorough with their hitch designs so I would not worry about this hitch not having the needed…

view full answer...

Answer 12

Hi Mark, it looks like you picked up the Curt hitch that fits the cab and chassis models of the 1977 Ford trucks. Do you know if your truck was originally built as a cab and chassis model which means it came with a slightly wider frame and was made…

view full answer...

Will I Lose the Tow Hooks When Installing a Front Hitch on a 2022 GMC Sierra 2500?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching