Replacement Red Lens for 2-1/2" Round LED Optronics Marker Clearance Light With 1 Diode

Question

Question:

Can you get a replacement lens for this light?

asked by: Wayne A

0

Expert Reply:

Yes, to replace the lens on your red Optronics LED Clearance or Side Marker Trailer Light w/ Reflector # MCL0040RBB you need the following:

- Replacement Red Lens for Optronics LED Side Marker / Clearance Light # OPT79NR

expert reply by: Jon G

0

Answer 1

Thank you for the photos, that really helps! It looks like you're needing the 1-diode 2-1/2" round lights from Optronics; Red #MCL0040RBB and Amber #MCL0040ABB. The lens looks to be the same design and the bases have the same mounting design…

view full answer...

Answer 2

Hey Jim, thanks for the picture. Based on seeing that the correct replacement lens would be the part #OPT79NR.

view full answer...

Answer 3

Normally the SAE number isn't a reliable way to pick out replacement lenses, but we know that the #A32RB is the correct replacement for a lens marked SAE-A-P2-DOT-02 like what you have. For an all new assembly you'd want the part #MC32RB.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Red Lens for 2-1/2" Round LED Optronics Marker Clearance Light With 1 Diode

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching