Replacement Bearing Kit for 5,200 lb Trailer Axle

Question

Question:

Do you know what bearing set i need for a Lippert axle 5200lbs #120064 Thanks

asked by: Tom C

0

Expert Reply:

For a 5,200 lb trailer axle the correct replacement bearing kit would be the part # BK3-300.

expert reply by: Jameson C

0

Answer 1

Hey Colton, thanks for reaching out! The correct replacement bearing kit for your 5,200 lb axle is the Bearing Kit #BK3-300. I was able to have my contact at Dexter Axle cross-reference these parts to make sure that's what came with your axle.…

view full answer...

Answer 2

Thank you for the picture which allows me to confirm the correct parts. Your Dexter D52 axles under your 2018 Coachmen Freedom Express Blast 271BL toy hauler came with the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459. We do have the…

view full answer...

Answer 3

Thanks for the picture! I reached out to Dexter with your information and you have a 5,200lb #11 torflex axle and you'll need the following parts: (2) Brakes with Parking Brakes #23-112-113 (2) Brakes without Parking Brakes #23-105-106 (4)…

view full answer...

Answer 4

Hello John, thanks for reaching out.The model number of your EZ Loader Trailer does indicate a 5,200 lb axle rating. The 5,200 lb axles do use a standard bearing combination, the #25580 (1.75" inner diameter) inner bearing and the #LM67048…

view full answer...

Answer 5

Hey David, thanks for the picture. I was able to track down a spec sheet for your Dexter axle which I have included below. The 031-029-02 bearing is item #15123 and the 031-030-02 bearing is item #25580. For a bearing kit you can use part #BK3-110…

view full answer...

Answer 6

The mounting holes of the Stabilizer Jack #TJ01RT are 7/16" in diameter so any bolt 1/32" smaller than that will fit the hole. The length is going to depend on your setup. The bolt thickness can be a bit smaller as long as the head of the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Bearing Kit for 5,200 lb Trailer Axle

Product Page this Question was Asked From

Continue Researching