Trailer Wheel Stud with Knurled Section Close to .53 inch

Question

Question:

Good Morning, I have a trailer with some older hubs. The wheel studs have a collar that presses in to the hub with a measurement of .530inch OD. Are there wheel studs available to replace these? Thank you

asked by: Randy A

0

Expert Reply:

We have the Kodiak wheel stud part # K12WB2 which is a 1/2 inch diameter wheel stud that has the press in section as .54 inches. This is closest option we have to what you need.

expert reply by: Jameson C

0

Answer 1

The Demco #DM72VR Hydraulic Trailer Brake Actuating Coupler would require four 1/2 x 4-1/2 inch grade 5 bolts to install it on a trailer tongue. I've linked to a product description video as well as a photo with the bolt spacing that you might…

view full answer...

Answer 2

The Dexter Wheel Bolt #7-262 that you referenced is indeed extremely close to the measurements on your existing bolt and it should work great as a replacement. This is the closet option we have available. I did also go out to our warehouse just to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Trailer Wheel Stud with Knurled Section Close to .53 inch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching